SampQOL OS User Manual
This manual is for SampQOL OS 0.3.0.
This manual shows only what SampQOL OS adds or changes. For all other functions, see the stock MPC Sample User Guide.
Introduction
What is SampQOL OS?
SampQOL OS is a mod for the MPC Sample. It adds functions that stock 1.3.0 does not have, for example more drum tracks, a mixer with inserts on pads, tracks and submixes, a Step Edit with a Track View, recording directly into the sequence, a looper, effects on the input, an EQ for each pad, export of stems, 16 USB outputs, a tuner, a sidechain and MIDI out for each track.
The functions stay close to the MPC workflow. The ideas come from different sources, most of all from the MPC One, Live and X.
- The mod starts by itself from the microSD card. Without the card, the MPC starts as stock 1.3.0.
- Your projects stay normal MPC projects. On a stock MPC Sample, the project opens, but the mod functions do not work there. See Compatibility and limitations.
Is it safe?
SampQOL OS does not change the stock firmware or the system files. A stock function runs a script from the SD card at start-up (the autorun folder). The script starts the stock MPC Sample software with the mod next to it. The mod is only in the memory (RAM): when you set the MPC off, it is gone.
Important: You use SampQOL OS at your own risk. SampQOL OS is a free mod. It is not a product of Akai Professional or inMusic, and they do not give support for it.
Tip: An error in the mod can stop the software while you play. Then you lose what you did not save. Save your project often, and keep a copy of your important projects.
About this manual
Names of buttons, knobs and settings are in bold. B1, B2 and B3 are the three buttons above the display. K1, K2 and K3 are the three knobs below the display.
Tip: A tip is in a block like this one.
Knobs on SampQOL screens
K1–K3 on the SampQOL screens act as stock knobs: they follow MIDI Config > Parameter Takeover (Pickup, Scaled or Instant). With Pickup, a small arrow next to the knob shows which way to turn. The FADER follows MIDI Config > Fader Takeover.
On a SampQOL page with its own K1–K3 (EQ, Tail, Scale, Kill EQ, an effect page), the ENCODER changes the last knob that you turned, in small steps. Push the ENCODER to go to the next knob (SHIFT: the previous knob), as in stock Chop Mode. With SHIFT held, the ENCODER changes the SHIFT value of that knob.
On the Tune page of SAMPLE, hold SHIFT and turn the ENCODER to change the knob in the focus box: Root (K1), Key (K2) or # Beats (K3). On the Play page it is the same for Pad Link (K2) and Stereo (K3). Push the ENCODER to move the focus box.
Five knobs step with the turn and never jump: Root and Key (SHIFT + K1 / K2 on the Tune page), Export (K1), the track color (K1) and the two EQ crossovers together (SHIFT + K2).
Quick overview
| Function | How to open it |
|---|---|
| Step Edit: Pad View | SHIFT + SAMPLE |
| Step Edit: Track View | SHIFT + SEQ |
| Mixer | PAD FX. Hold PAD FX + pad or ENCODER: select a pad, track or submix |
| Rename a track, submix or pad | PAD FX, the Pad, Track or Submix page, SHIFT + B1 |
| Select a track | Hold PAD BANK + turn the ENCODER, or SHIFT + PAD BANK + pad 1 to 16 |
| Select a sequence | Hold SEQ + push a pad, or turn the ENCODER |
| To Seq and Looper | SAMPLE RECORD, B2 (To Seq), B3 (Looper) |
| Export mixdown and stems | SHIFT + PAD 16, B3 (Export) |
| Chop Mode: 128 slices, Link Slices, Extract | Chop Mode: PAD BANK, SHIFT + K3, SHIFT + B1 |
| EQ for each pad | SAMPLE, B3 until the EQ page shows. Or PAD FX, row EQ |
| Record mutes | MUTE during SEQ RECORD + PLAY |
| Track mute | PAD BANK + MUTE, or hold MUTE for 0.7 seconds |
| Mute Type: Audio or Event | Settings > Mute Type |
| Mute groups | Mixer, K2 (Pad Grp, Trk Grp, Sub Grp) on the Pad, Track or Submix page; SHIFT + K2 on the Ch. Mixer and Pad Mixer |
| KEYS (MIDI keyboard) | Play the keyboard. Root note: SAMPLE, Tune page, SHIFT + K1 |
| MIDI out for each track | PAD FX, B1 to Track, SHIFT + K3 (also on the Ch. Mixer) |
| Settings | SHIFT + PAD 8 (MIDI Config), then B2 |
| Undo counter | SHIFT + - or SHIFT + +: the popup shows "Undo 2/7" |
| New folder | SAMPLE SELECT, External, select a folder, B3 |
| Delete folder | SAMPLE SELECT, External, select a folder, SHIFT + B3 |
| 16 LEVELS Scale, Chord, Arp | 16 LEVELS on, SHIFT + 16 LEVELS until "Scale" |
| Sample Tail | SAMPLE, B1 until the Tail page shows |
| Stereo: one channel of a sample | SAMPLE, Play page, SHIFT + K3 |
| Automate (fades) | Track View (SHIFT + SEQ), SHIFT + B2 |
| Duplicate a track | Track View (SHIFT + SEQ), SHIFT + B3, then B2, then B3 |
| Explode a track | Track View (SHIFT + SEQ), SHIFT + B3, then B3, then B3 |
| Delete a track | Track View (SHIFT + SEQ), SHIFT + B1 |
| Move a track | Hold PAD BANK + - or + |
| Select grid | Hold PAD BANK or SEQ: a 4x4 grid of the tracks or sequences. B2: grid on or off |
| Name a sequence | SEQ screen, SHIFT + B3 |
| Sidechain: Mother Ducker | PAD FX, an empty slot, B3, Dynamics > Mother Ducker Input and Mother Ducker |
| Kill EQ insert | PAD FX, an empty slot of a track, submix or the master, B3, EQ/Filter > Kill EQ |
| Track Volume on the FADER | SHIFT + PAD 9, Track Volume |
| Fader Overrides | SHIFT + PAD 9, then B2. Or Settings > Fader Overrides |
| Resample one pad | SHIFT + PAD 11, B2 (Pad) |
| Preview a sample | SAMPLE SELECT, a pad; SHIFT + K2 = Preview / Own Sample |
| Save to a folder | Save Sample or Save Project, B3 (Do It!) |
| Home Folder | Settings > Home Folder, then Sample Select Opens |
| Random project name | Save Project, SHIFT + B3 |
| Template for New Project | Settings > Default Template |
| Load a drum program (.xpm) | SHIFT + PAD 16, Load Project, select the .xpm file, B3 (Load Kit) |
| Swap two pads | SHIFT + ERASE (COPY), one pad with a sample, B2 (Swap) |
| Erase all automation | ERASE + knob, fader or pad, then B2 (All) |
| Erase all automation of a track | Track Mute, ERASE + pad, then B2 (All) |
| Erase automation in the mixers | Ch. Mixer or Pad Mixer: ERASE + K1, K2, FADER or B3. Insert or effect page: ERASE + knob, ENCODER push or B3 |
| Knob FX List and Insert FX List | Settings > Knob FX List, Insert FX List |
| Change the Knob FX on any screen | Hold KNOB FX + turn the ENCODER |
| Knob FX Bypass on B3 | KNOB FX bar, B3 |
| Clear a song, Quick Add | SHIFT + PAD 12 (Song), SHIFT + B2. Settings > Song Pads |
| Tuner | SHIFT + PAD 7 |
| Key of a sample | Tuner, B2 (Key). By hand: SAMPLE, Tune page, SHIFT + K2 |
| AIR Compressor, AIR Stereo Width | PAD FX, an empty slot, B3, Dynamics or Modulation |
| AIR Lo-Fi | PAD FX, an empty slot, B3, Harmonic |
| AIR Pitch Shifter | PAD FX, an empty slot, B3, Modulation |
| Loop a part | Track View (SHIFT + SEQ) or Pad View (SHIFT + SAMPLE): a selection, then SHIFT + PLAY |
| Record rear and USB at once | SAMPLE RECORD, K1 = Rear+USB |
| Effects on the input | SAMPLE RECORD, SHIFT + B2 |
| 16 USB outputs | Settings > 16 USB Outputs, then PAD FX, K3 (Out) |
| Sleep | Settings > Sleep |
| Screen Mirror | Connect the USB cable, open http://mpc-sample.local:7410 in a browser |
| Stock Pad FX | SHIFT + PAD FX, then B2. At once: Shift+PAD FX = Pad FX |
Installation and start-up
You need:
- A microSD card with the format exFAT. The card can have any name.
- A computer (Mac or Windows) with a card reader.
- The zip file of SampQOL OS, for example SampQOL-OS-v0.3.0.zip. Use the file with the highest number.
Install
- Check the MPC. Start the MPC without the SampQOL card. Push and hold SHIFT and push PAD 8 – MIDI CONFIG. The top right of the display must show v1.3.0 (full number 1.3.0.12). If not, see Troubleshooting.
- Copy. Unzip the zip file. Put the microSD card in the computer. Drag the folder autorun from the unzipped folder onto the card (Mac: in Finder; Windows: in File Explorer). Then eject the card.
- Start. Set the MPC off. Put the card in the MPC. Set the MPC on.
- SampQOL OS starts by itself. You do not push a button.
The display shows the SAMPQOL logo, the version (v0.3.0) and beatops.io/SampQOL until the app is ready.
Every start
You cannot select stock at start-up. To start stock 1.3.0, set the MPC on without the SD card, or see Go back to stock.
To see if the mod runs: MIDI Config (SHIFT + PAD 8) shows the mod version top right, for example QOL-0.3.0 (stock: v1.3.0).
SD Card Access (SHIFT + PAD 16) works as in stock, also with a card named MPC SAMPLE. If the MPC shows SD card is busy, do not copy files: push B3 (OK), push Exit and try again. If SampQOL OS crashes during SD Card Access, see The computer lost the SD card.
Watchdog
A watchdog monitors the mod. If the mod crashes, the watchdog starts SampQOL OS again in a few seconds. You lose only what you did not save. If the mod crashes again within 2 minutes, the MPC starts as stock. Each crash is written to the folder autorun/logs on the card (last-exit.log holds the crash details). Send this folder with a bug report.
Project safety net
At each start-up (before SampQOL OS starts) and after a crash, stock can load the open project and delete the samples that only SampQOL OS uses, for example the samples of tracks 2-16. Thus SampQOL OS keeps a copy of the open project in the background. The copy uses no extra space for the samples of the project. A sample that you erase stays in the copy for some time, at most until the internal storage has less than 512 MB free.
When SampQOL OS starts:
-
If stock did not change the project, the missing samples come back, without a message.
-
If stock changed the project, your last SampQOL OS version is the project QOL-Recovery-<date> (Projects > User). After the load, the SAMPLE screen asks RECOVERY with its name:
- B3 (Load): loads your last SampQOL OS version. Save then offers the name of your original project. The QOL-Recovery project stays.
- B2 (Delete): deletes the QOL-Recovery project and its samples. Your open project does not change.
- B1 (Cancel): keeps the QOL-Recovery project. The MPC does not ask again for it.
Only the newest QOL-Recovery project stays: a new one deletes the older one, unless you saved over it.
When you load another project, the copy of the old project goes at once. The old project stays where you saved it.
Tip: A stock question that opens over RECOVERY closes it; the MPC asks again at the next start. You can also load or delete a QOL-Recovery project in the browser. Delete it when you do not need it, to free internal storage.
Two rules
Important: SampQOL OS is only confirmed to work with 1.3.0. After a firmware update, it will probably not work. Ignore the updates on the Akai web page (mpc-sample.local) and in the inMusic Software Center.
Important: Save your project before you put the card in an MPC that is on. SampQOL OS then starts at once and restarts the MPC software, and you lose what you did not save.
Go back to stock or install a new version
- Stock for one session: start without the SD card.
- Stock with the SD card in (for example, to use your projects on the card): on a computer, rename the folder autorun (for example to autorun-off) or move it into another folder. The MPC starts SampQOL OS only from a folder autorun directly on the card. To start SampQOL OS again, put the name and place back.
- Stop for good: delete the folder autorun from the card.
- New version: delete the folder autorun from the card. Then do step 2, 3 and 4 of Install with the new zip file. Your settings stay: mpcqol.conf is on the top level of the card, not in the folder autorun.
Settings
- Push and hold SHIFT and push PAD 8 – MIDI CONFIG.
- Push B2 to go to Settings. If Shortcuts > Shift+Pad 8 is Settings, the MPC skips this step.
- Turn the ENCODER to select a line. Hold SHIFT and turn the ENCODER to go to the first line of the next or previous group.
- Push the ENCODER (the line becomes blue), turn it to change the value, and push it again. A line with > opens its list or page.
- Push B1 (Back) or B2 to go back to MIDI Config.
The mod saves the settings on the SD card (mpcqol.conf).
| Group | Setting | What it does | Values |
|---|---|---|---|
| PROJECT | Default Template | The project that New Project can load. See New Project with a template. | None (default), a project |
| PROJECT | Start Drive | The drive of Load Project, and of the first Save Project folder page after start-up. Last Used = as in stock. Without an SD card, the MPC uses Internal. | Internal, External (default), Last Used |
| PROJECT | Sequence Preset Names, Track Preset Names, Submix Preset Names, Pad Preset Names | The names in the Preset list when you rename. | On (default), Off for each name |
| SAMPLE BROWSER | Start Drive | The drive of Sample Select, and of the first Save Sample folder page after start-up. Last Used = as in stock. | Internal, External, Last Used (default) |
| SAMPLE BROWSER | Sample Select Opens | Where Sample Select opens. Last Used = the Start Drive of SAMPLE BROWSER. | Last Used (default), Home Folder |
| SAMPLE BROWSER | Home Folder | See Home Folder. | None (default), a folder |
| SAMPLE BROWSER | Sample Select Pads Play | What a pad does in Sample Select (also SHIFT + K2 there). See Preview in Sample Select. | Preview (default), Own Sample |
| SAMPLE | Snap to Zero Crossing | Stock: only the trim snaps to a zero crossing, only zoomed out. Always: also chops and slices, at every zoom. | Stock (default), Always |
| SAMPLE | Link Slices Default | Link Slices for each pad that has no own choice. See Chop Mode. | Off, On (default) |
| SAMPLE | Ask Before Rechop | When Chop Mode asks before K3 makes new slices. After Edits: only after your own slice edits. Always: every time the type is Manual. | After Edits (default), Always |
| SAMPLE | Threshold Max Slices | The most slices of Chop Type Threshold. Fewer slices keep the markers apart on a short sample. See Chop Mode. | 16 (default), 32, 64, 128 |
| SAMPLE | Ask Before Erase Pad | On: with the sequence stopped, ERASE + a pad with a sample asks "Erase Pad A01?" (B1 = Cancel, B3 = Do It!). The pads do nothing while it asks. While the sequence plays, ERASE + pad erases the notes of the pad, as in stock. UNDO brings a cleared pad back. | Off (default), On |
| SAMPLE | Pad EQ | On: the EQ page shows and you hear the EQ. Off: as in stock; the EQ values stay in the project. | Off, On (default) |
| SAMPLE | Sample Screen Name | The name that the SAMPLE screen shows. | Pad (default), Track, Sequence |
| SAMPLE | MIDI Keyboard Plays | For a pad with no own KEYS root. Selected Pad: the keyboard plays the selected pad chromatically. All Pads: as in stock. | All Pads, Selected Pad (default) |
| SAMPLE | MIDI Keys on Chop Pad | A MIDI keyboard on a pad with 2 or more slices: one slice per key, or the pad chromatically. | Slices (default), Pitch |
| SAMPLE | Auto Key | A new sample from Sample Select, Sample Record or Resample gets its key at once. See Find the key of a sample. | New Samples (default), Off |
| SEQUENCE | Track View Labels | The Track View row labels: track number or name. | T01 (default), Name |
| SEQUENCE | Track View Rows | The tracks that the Track View shows. The FADER can change it: see Fader in Step Edit. | 16, 12, 8 (default), 6, 4, 2, 1 |
| SEQUENCE | Track View Order | 1 Top: track 1 on the top row. 1 Bottom: track 1 on the bottom row. | 1 Top (default), 1 Bottom |
| SEQUENCE | Pad View Rows | The pads that the Pad View shows. The FADER can change it: see Fader in Step Edit. | 16, 12, 8 (default), 6, 4, 2, 1 |
| SEQUENCE | Pad View Order | 1 Top: pad 1 on the top row. 1 Bottom: pad 1 on the bottom row, as on the pads. The Track View shows the pads of the cursor track in the same order. | 1 Top (default), 1 Bottom |
| SEQUENCE | Pad View Grid | The step size when you set Steps on in the Pad View. | 1/8, 1/16 (default), 1/32 |
| SEQUENCE | Position Shows | The position in the top line of Step Edit. Playhead: the playhead while the sequence plays, else the cursor. | Playhead (default), Cursor |
| SEQUENCE | Shift+Play Starts | SHIFT + PLAY with no selection and no loop in the Track View or Pad View. Playhead: stock CONTINUE. Cursor: start at the cursor. | Playhead (default), Cursor |
| SEQUENCE | Triplet Grids | Hide: no T values in the grid lists (Pad View zoom, SEQ screen K2, Rec Quantize popup). | Show (default), Hide |
| SEQUENCE | Count-In at Start | Count-In when the MPC starts. SHIFT + PAD 4 changes it until the next start. | On (default), Off |
| SEQUENCE | Track Grid on Screen | The select grid of the tracks. | Toggle (default), On, Off |
| SEQUENCE | Seq Grid on Screen | The select grid of the sequences. | Toggle (default), On, Off |
| SEQUENCE | Mute Type | How a pad mute or a track mute sounds. Audio: the sound stops at once (a track fades out in 5 ms). Event: no new notes; the notes that sound play to their end. See Mute Type. | Audio (default), Event |
| SEQUENCE | Song Pads | What a pad does in Song mode. See Quick Add in Song mode. | Stock (default), Quick Add |
| FX & AUTOMATION | Knob FX List > | See Knob FX List and Insert FX List. | On or Off for each effect (default: all On) |
| FX & AUTOMATION | Knob FX B3 Bypass | On: while the KNOB FX bar shows, B3 turns the Knob FX on or off. Off: B3 does the function of the screen under the bar. See Knob FX Bypass on B3. | On (default), Off |
| FX & AUTOMATION | Insert FX List > | See Knob FX List and Insert FX List. | On or Off for each effect (default: all On) |
| FX & AUTOMATION | FX Categories | On: the Insert FX list shows the effects in 6 categories. Off: one long list. | On (default), Off |
| FX & AUTOMATION | Erase All Starts | If All is on when the ERASE PAD AUTOMATION, ERASE TRACK AUTOMATION or ERASE SUBMIX AUTOMATION window opens. | On, Off (default), Last Used |
| FX & AUTOMATION | Mixer Opens On | The first page of the Mixer. | Pad inserts, Ch. Mixer, Last Used (default) |
| SYSTEM | Shortcuts > | See Shortcuts. | See Shortcuts |
| SYSTEM | Fader Overrides > | What the FADER does in Sample Select, in the Pad View and Track View, and on the Pad FX screen with Fixed on. See Fader Overrides. | See Fader Overrides |
| SYSTEM | CPU/RAM Monitor | A bar with the CPU and RAM use. Warn Only: only for high CPU or RAM, or audio dropouts. | Off (default), On, Warn Only |
| SYSTEM | Show Knob Values | Stock: a knob shows its label, and its value for a short time when you turn it. The Mixer Out (K3) and group (K2) and the Mother Ducker Bus (K1) always show their value. Always: every knob shows its label and its value, with a short label when needed ("Freq", "Semi"). | Stock (default), Always |
| SYSTEM | Screen Brightness | The maximum brightness of the display. | 13%, 25%, 50%, 100% (default) |
| SYSTEM | Pad Brightness | The brightness of the pad lights (not the buttons). | 25%, 50%, 75%, 100% (default) |
| SYSTEM | Tap Tempo Light | Dimmed: the TAP TEMPO light stays on, a little dimmed. Blink: it flashes with the tempo, as stock. With SHIFT held, it shows the SHIFT colour, as in stock. | Dimmed (default), Blink |
| SYSTEM | Sleep | The screen and all lights go off after this time with no input. See Sleep. | Off (default), 5 min, 10 min, 20 min, 30 min |
| SYSTEM | 16 USB Outputs | On: 16 more USB audio outputs to a computer. It applies after a restart. See 16 USB outputs. | Off (default), On |
Shortcuts
Give SHIFT + a pad, SHIFT + SAMPLE, SHIFT + SEQ, PAD FX and SHIFT + PAD FX a different function.
In Settings, select Shortcuts (group SYSTEM). Push the ENCODER, and change each button as a Settings line.
| Button | Default | Other functions |
|---|---|---|
| Shift+Pad 1–6, Shift+Pad 12–15 | Stock | View Follow, Count-In, Pad View, Mixer, Off, Input Config, Pad FX, Tuner |
| Shift+Pad 4 | Count-In (stock) | View Follow, Pad View, Mixer, Off, Input Config, Pad FX, Tuner |
| Shift+Pad 7 | Tuner | Stock (Double Speed), View Follow, Count-In, Pad View, Mixer, Off, Input Config, Pad FX |
| Shift+Pad 8 | MIDI Config | Settings |
| Shift+Sample | Pad View | Input Config (stock), Mixer, Off, Pad FX |
| Shift+SEQ | Track View | Pad View, Mixer, Off, Input Config, Pad FX |
| PAD FX | Mixer | Pad FX (stock), Pad View, Input Config |
| Shift+PAD FX | Flex Beat (stock) | Pad FX, Last Used |
Stock = the stock function of the pad. Off = the button does nothing. Settings = SHIFT + PAD 8 opens Settings at once (B1 or B2 goes to MIDI Config). View Follow: see below. The other functions open that screen: the stock COUNT-IN, Pad View, Mixer, the stock Input Config menu, the stock Pad FX screen, the Tuner.
Tip: When you move Pad View off Shift+Sample or Mixer off PAD FX, set a Shift+Pad to it to keep it at hand.
Tip: While COPY (SHIFT + ERASE) is open, each pad is a COPY destination, also when you still hold SHIFT. The Shift+Pad functions do not start then.
Tip: By default, SHIFT + PAD FX opens Flex Beat, and the stock Pad FX screen is on B2 there. With Shift+PAD FX = Pad FX, SHIFT + PAD FX opens the stock Pad FX screen at once, and Flex Beat is on B2 of that screen. With Shift+PAD FX = Last Used, SHIFT + PAD FX opens the screen that B2 went to last: Flex Beat or Pad FX. After a restart, it opens Flex Beat.
Tip: SHIFT + SEQ is the only button that opens the Track View. With another function on Shift+SEQ, you cannot open the Track View.
Tip: More than one pad can have the same function. A pad with a new function loses its stock function. Example: with Shift+Pad 5 = Mixer, SHIFT + PAD 5 then does not open the master Color Comp. Open it in the Mixer (Master, Edit).
Tip: SHIFT + PAD 9, 10, 11 and 16 always keep their stock function: the mod adds its own functions to those screens.
View Follow
View Follow sets what the Pad View and the Track View follow while the sequence plays: Follow Playhead (the view scrolls with the playhead, the cursor stays) or Follow Cursor (the view stays at the cursor). Set a Shift+Pad to View Follow. Each push of SHIFT + that pad sets the other value, with a popup.
Tip: Turn the ENCODER or push - or +: Follow Playhead stops until the next start of the sequence. The MPC keeps your choice after a restart.
Fader Overrides
Set what the FADER does in Sample Select, in the Pad View and Track View, and on the Pad FX screen with Fixed on. Fader Menu = the FADER does its FADER menu function there (for example Pad Volume).
- Push and hold SHIFT and push PAD 9. The FADER menu opens.
- Push B2 to go to Overrides.
- Turn the ENCODER to select a line.
- Push the ENCODER (the line becomes blue), turn it to change the value, and push it again.
- Push B1 (Back) or B2 to go back to the FADER menu.
The same page is in Settings > Fader Overrides (group SYSTEM). There, B1 (Back) or B2 goes back to Settings.
| Setting | What it does | Values |
|---|---|---|
| Sample Select | Scroll: the FADER scrolls the list in SAMPLE SELECT and Load Project (up = the first row). | Fader Menu, Scroll (default) |
| Pad / Track View | What the FADER does in the Pad View and the Track View. Nudge (as in stock): it moves the note. Zoom: it sets the rows that the view shows. See Fader in Step Edit. | Nudge, Fader Menu, Zoom (default) |
| Pad FX (Fixed) | On the stock Pad FX screen with Fixed on. Effect Mix: the FADER sets how much of the held effects you hear. Fader Menu: a tap still holds the effect, at the pad velocity. See Pad FX: Fixed. | Effect Mix (default), Fader Menu |
Tip: Zoom is the default for a new install. A value that you saved before stays.
Sample Mode
The SAMPLE screen header
The SAMPLE screen shows the sequence and the track before the pad, for example "S01 T02 A01" (T03+ = a new track).
- While you hold SEQ or PAD BANK, S01 or T01 is red and the name field shows the sequence or track (that you will get).
- While a selected sequence waits for the end of the loop, S01 is red and the name field shows "Next" and its name.
- While you hold SAMPLE, A01 is red. SAMPLE + pad selects that pad without sound (stock).
EQ page
Each pad has a 3-band EQ, directly after the filter. At 0 dB, the EQ does not change the sound, and it uses no extra CPU.
- Push SAMPLE and select a pad.
- Push B3 until the EQ page shows (Filter > Flt Env > EQ).
- Turn the knobs:
- K1 = Low, K2 = Mid, K3 = High.
- Fully left = the band is off (kill). Center = 0 dB. Fully right = +6 dB.
- Crossover points:
- SHIFT + K1 = crossover Low/Mid (40 Hz – 1 kHz).
- SHIFT + K3 = crossover Mid/High (600 Hz – 15 kHz).
- SHIFT + K2 = moves the two crossovers together.
The window shows a live spectrum of the pad (after the EQ) with the EQ curve. For the ENCODER, see Knobs on SampQOL screens.
- Automation: turn K1–K3 during SEQ RECORD and PLAY.
- Erase automation: push and hold ERASE and turn K1, K2 or K3 on the EQ page. With SHIFT, you erase the crossovers.
- The project saves the EQ values for each pad.
- Bypass: SHIFT + B3 on the EQ page: all pads play without the EQ, and the knobs show grey. Push again to hear the EQ. Bypass goes off when you leave the EQ page. The project does not save it.
- Mixer: PAD FX goes to the inserts of the pad. B3 on the row EQ comes back. See Mixer.
Tip: The EQ plays only on the MPC Sample with SampQOL OS. For an EQ that plays on every MPC, put an EQ effect on the pad as an insert in the Mixer.
Sample Tail
With Tail, the end of a sample (or chop) sounds longer: the last part plays back and forth (ping-pong) and fades out, so a chop does not stop abruptly.
- Push SAMPLE and select a pad.
- Push B1 until the Tail page shows (Trim > Mix > Amp Env > Tail).
- Turn the knobs:
- K1 = Start: the size of the part that plays back and forth (4 ms to 1 s), with a blue line in the waveform.
- K2 = Length: how long the tail sounds (4 ms to 5 s). Fully left = Off (default).
To erase the Tail automation of the pad, hold ERASE and turn K1 or K2.
- Tail does not work when Loop is on.
- The pad light stays bright while the tail plays.
- In Chop Mode, Tail is for the selected chop.
- The project saves the Tail values.
Stereo: one channel of a stereo sample
With Stereo, a stereo sample plays only its left channel, only its right channel, or a blend. The channel plays in mono, on both speakers.
- Push SAMPLE and select a pad.
- Push B2 until the Play page shows.
- Hold SHIFT and turn K3 (Stereo):
- St (centre, default): the sample plays in stereo, as in stock.
- L Mono (fully left): only the left channel, on both speakers.
- R Mono (fully right): only the right channel, on both speakers.
- L1 to L49, R1 to R49: a blend. The other speaker plays more of the channel that you keep. The higher the number, the more mono the sound is.
- A mono sample does not change.
- The project saves the Stereo value of each pad.
- A turn during SEQ RECORD + PLAY does not record automation.
Tip: Put L Mono and R Mono on two pads with the same stereo sample: each pad plays one side as its own mono sound.
Tip: For left and right together as one mono sound, keep Stereo at St and put AIR Stereo Width with Width 0 % in a pad insert slot.
Tip: On a stock MPC Sample and on an MPC One, Live or X, the pad plays both channels. To keep the result in the sample, use Resample one pad first.
16 LEVELS Scale
With Scale, the 16 pads play the sample of one pad on the notes of a scale. You can also play a chord on each pad, or an arpeggio (Arp).
- Push SAMPLE and select a pad.
- Push 16 LEVELS to set 16 Levels on.
- Push SHIFT + 16 LEVELS until the display shows "16 Level / Scale" (Velocity > Filter > Tune > Scale; again = Velocity).
- Turn the knobs on the orange bar:
- K1 = Key (C to B).
- K2 = Scale: Chromatic, Major, Minor, Harm Minor, Maj Pent, Min Pent, Dorian, Phrygian, Mixolydian, Blues.
- K3 = Octave (-2 to +2).
- The ENCODER: see Knobs on SampQOL screens.
- Play the pads (orange). PAD 1 plays the key, the pads above it go up the scale. Example: Key C, Major: PAD 1 to PAD 8 play C, D, E, F, G, A, B, C.
Tip: push SAMPLE or 16 LEVELS to set 16 Levels off and play the normal pads again. This is for all 16 Levels types. In stock, SAMPLE does nothing in 16 Levels.
The key plays at the nearest pitch (up to 5 semitones up or 6 down). Use Octave for more. Scale uses the KEYS root note of the pad, for example "Key C (D3)". With the KEYS root Off, the sample is a C.
Chord: hold SHIFT and turn K1: Chord Off, 1-3-5, 1-3-5-7, 1-3-5-6, 1-3-5-9, 1-3-5-7-9, 1-2-5, 1-4-5, 1-5, 1-5-8. The numbers are the steps of the scale (8 = one octave up). With Chromatic, each pad plays the chord shape of Major (1-3-5 = major, 1-4-5 = sus4). On a pad in Note On mode, each recorded tone plays with its own length.
Arp: hold SHIFT and turn K2 to select a pattern: Arp Off, Up, Down, Up & Down, Converge, Diverge, Thumb Up, Pinky Up, Random. SHIFT + K3 sets the number of octaves (1 to 4).
Hold NOTE REPEAT and hold pads: the repeats play the notes of the held pads (with Chord: all chord tones) one at a time, in the pattern, from low to high. A note that two chords share plays one time. Rate, swing and recording are as stock Note Repeat.
Tip: With Chord Off, one pad plays the same note on each step. Hold two or more pads, or set a Chord.
Pad grid: B2 (Grid) shows or hides a 4×4 grid with the note (for example E3) and the chord name (for example Em7) of each pad. The pads that play the key are orange. When the grid is off, it shows for 2 seconds after you turn a knob.
- While you hold SHIFT, the bar shows the Chord and Arp values. SHIFT + pad always does the stock function.
- Two pads: a second pad stops the first, as in stock. The second pad plays until you release it.
- The mod saves the Scale values on the SD card, not in the project.
- A recording is a normal 16 Levels note. The project also opens on a stock MPC.
- A recorded chord keeps all tones, also with Time Correct (SHIFT + PAD 14): the first tone goes on the grid, each next tone 1 tick (1/960 of a beat) later. Stock keeps only one tone. This is for all 16 Levels notes, also Tune.
Tip: A pad in Mono mode plays only one tone, so while Scale plays a Chord, the 16 Levels pad stays in Poly. A Mono pad goes to Poly at once, also after UNDO, a project load or on another track. The setting is a normal pad setting (Play page, K1) and is saved with the project. UNDO does not take it back. To keep the pad in Mono, set Chord Off. Arp with Chord Off does not change the pad.
Tip: To play the Scale notes and chords on an external synth, give the track its own MIDI channel (see MIDI out). A track with Glob. sends only the source note.
Note: Scale does not work when Warp is on in mode Pitch (as stock Tune). Set Warp to Off or to Time stretch (SHIFT + PAD 15).
KEYS: play a pad from a MIDI keyboard
With KEYS, a MIDI keyboard plays the selected pad chromatically. The pads stay drums; the keyboard plays your sample at pitch.
Connect the keyboard:
- Connect a keyboard with a MIDI output with a 1/8" (3.5 mm) TRS to 5-pin MIDI DIN cable (not included) to MIDI IN. A keyboard with only USB: use a USB MIDI host box (not included) to MIDI IN, or a computer that sends its MIDI to the MPC over USB-C.
- In MIDI Config (SHIFT + PAD 8), set MIDI Port to External (MIDI IN) or USB (computer), and Pad MIDI In to On.
Tip: A keyboard directly on USB-C does not work: the MPC is a USB device, not a USB host. With the wrong MIDI Port, the keyboard plays no sound.
Play: push SAMPLE, select a pad (SAMPLE + pad: no sound) and play the keyboard. C3 plays the sample at its original pitch. Chords, release per key and the sustain pedal work.
Change the root note of a pad:
- Push SAMPLE and push B2 until the Tune page shows.
- Hold SHIFT and turn K1 (Root): one step = one semitone.
- Below C#-2 is Off: the keyboard plays the pads as in stock.
- Below Off is Default: the pad follows Settings > MIDI Keyboard Plays. The value shows in brackets, for example "(C3)".
The project saves the root note of each pad.
Tip: The Tuner can set the root note from the note that the pad or the instrument plays.
Chopped pad: on a pad with 2 or more slices, each key from the root note up plays one slice (1, 2, ...) at the original pitch. For the pad chromatically, set Settings > MIDI Keys on Chop Pad to Pitch.
NOTE REPEAT: hold a key. The selected pad repeats at the pitch of that key.
Record: set SEQ RECORD on and play. The MPC records normal 16 Levels notes (Tune, or Slice on a chopped pad), so the project also opens on a stock MPC. Recorded chords work as in 16 LEVELS Scale.
Tip: A key does not add a note in Step Edit, as in stock. Use the pads there.
Chop Mode
Chop Mode cuts a sample into slices. SampQOL OS adds 128 slices, chop by tap, more Chop Types, Link Slices and a new Extract.
Slices and banks
128 slices: Chop Mode can have up to 128 slices on one sample. PAD BANK selects the bank (A = slices 1-16 to H = 113-128). ERASE + pad works on each bank. On a bank without chops, Chop Mode opens on bank A. When you close Chop Mode, the SAMPLE screen shows the bank of before Chop Mode again.
A sample without chops: Chop Mode opens with Chop Type Manual and one slice: the whole sample. Chop it by tap, or turn K3 to Threshold or Regions. Stock starts a Threshold chop there, and on a long sample that takes long.
Chop by tap
With Chop Type Manual, tap pad 1 to play the sample, then tap pads 2-16 in time with it. Each tap makes a chop. After the 16th chop of a bank, the next bank shows: tap its pad 1 and continue.
Tip: A chop between two chops does not change the bank. PAD BANK while the sample plays goes to the next bank. After chop 128 the bank does not change.
Threshold, Regions and Split
Threshold and Split: Chop Type Threshold makes up to 16 slices (bank A), as in stock. Set up to 128 in Settings > Threshold Max Slices. The first slices come from the start of the sample. A lower Threshold gives more slices. Split (SHIFT + B2) splits up to 64 slices.
Regions 32, 64 and 128: K3 (Chop Type) has 8 positions: Threshold, Regions 4, 8, 16, 32, 64, 128, and Manual. When you turn K3 or the encoder, the knob shows the name of the type.
When you leave Chop Mode or go to another track there, a Threshold or Regions chop becomes Manual, as the pads that Extract makes. The slices stay. To chop again, turn K3 to Threshold or Regions.
Note: Stock MPC Sample software chops a Threshold or Regions pad again and keeps only 16 slices. A Manual pad keeps all its slices, also on a device without the mod.
Tip: After a new chop or a moved slice, the MPC saves the chops in the sample file when you leave Chop Mode. A long sample then shows a loading circle for some seconds before the waveform comes back. Without a change, the waveform shows at once.
Tip: At 64 slices or more, Split stays white but does not split. Use Merge first, or add a slice by hand.
Link Slices and other options
Link Slices: when Link Slices is on, the start of the next slice moves with the end of a slice. Hold SHIFT and turn K3 (Link: On / Link: Off) for this pad. The project saves the choice of each pad. A pad with no own choice follows Settings > Link Slices Default. With Chop Type Threshold, SHIFT + K3 stays the stock Threshold.
Ask before rechop: before a new Chop Type (K3) replaces your own slices, the MPC asks "CHANGE CHOP TYPE": B1 = Cancel, B3 = Do It!. See Settings > Ask Before Rechop.
Zero crossing: with Settings > Snap to Zero Crossing = Always, Start, End, Loop, chops and slices snap to a zero crossing at every zoom, for fewer clicks.
Extract
Extract puts the chops of a pad on their own pads. It makes no new WAV: each new pad is a copy of the chopped pad, with the chop as its Start and End. The stock Extract (a new WAV for each chop) is not available.
- Push SAMPLE, select a chopped pad and open Chop Mode.
- Select a slice.
- Hold SHIFT and push B1 (Extract):
- B1 = Cancel.
- B2 = Pad: the selected slice goes to one pad.
- B3 = Track: each chop goes to its own pad, in order, in a row.
- Push the pad for the chop (Pad) or for the first chop (Track). A short push of PAD BANK selects the next bank, or hold PAD BANK and push a pad to select that bank. The display shows the pads (for example "16 chops to B01-B16") and if they are empty. At the start, the first empty pad (or row of pads) is selected, or else the last pad where the chops fit (128 chops: always A01). The pad lights show the pads in the bank: yellow = a chop goes there, red = a chop replaces the sample there, white = the chopped pad.
- If you want, turn K2 (Mute Grp) or the ENCODER to set the mute group of the chop pads: Off or 1-32 (one group per step of the ENCODER). At the start, it is the mute group of the chopped pad. Back keeps the value you set. In a mute group, a pad stops the other pads of that group, so a chop stops the chop before it. See Mute groups.
- Push a button:
- B3 = Do It! when all the pads are empty. When a pad in the way has a sample, B3 = Replace: the chops replace the samples on those pads. With Track, this can also be the chopped pad: it becomes its own chop, with that chop as its Start and End.
- B2 = New Track (Track only): the chops go to pads A01 and up of a new track directly after the current track. The MPC shows the new track in bank A, with pad A01 (the first chop) selected.
- B1 = Back: back to step 3.
- When the chopped pad has pad insert effects, New Track asks first: B3 (To Track) puts the effects one time on the track inserts of the new track, with the same settings and on/off state (the chop pads get no effects). B2 (Copy FX) gives each chop pad a copy. B1 (Back) goes back to step 4. The chopped pad keeps its effects. When an effect cannot be copied, the display shows "FX Cannot Be Copied" and nothing changes.
- The display shows "Extracted to:" and the pad or pads.
- One UNDO removes the full Extract, also a new track.
- With Pad, the chopped pad is never replaced. With Track and Replace, the chopped pad keeps its sample but plays only its own chop. UNDO gives back the chopped pad with all its chops.
- SHIFT + B1 on a pad that plays only its own chop shows "Extract: 1 chop". UNDO gives back all its chops.
- When the chops go past H16, the display shows "they do not fit" and B3 is not available. Push an earlier pad, or use New Track.
- 128 chops fill all pads of a track, so use New Track.
- With 16 tracks, New Track shows "16 Tracks Max".
- Extract works only when the sequence is stopped. The notes do not change.
Sample Record Mode
All settings of the stock Input Config menu are on the SAMPLE RECORD screen. For the menu itself on SHIFT + SAMPLE, see Shortcuts.
What you hear on the input is what you record: only the effects of the Input FX page (SHIFT + B2). The Knob FX does not play on the input (in stock, the monitor always goes through the Knob FX). Rec Input Effects in the Input Config menu does nothing. A change of Monitor (Off, Auto, On) gives no click. The monitor follows MAIN VOLUME.
Undo and Redo (SHIFT + - / +) work on SAMPLE RECORD. While a recording runs, the MPC shows Stop the recording first.
Input FX: effects on the input
Put up to 3 insert effects on the input, for example a compressor or a filter on a synth at the rear input. You hear them on the monitor and they go into the recording.
- Push SAMPLE RECORD.
- Push SHIFT + B2. The Input FX page opens.
- Select an empty slot with the ENCODER and push B3 (Insert).
- Select an effect in the Insert FX list.
The page works as the Insert pages of the Mixer:
- ENCODER: select a row. ENCODER push: the effect on or off.
- B3 = Insert (empty slot) or Edit (the effect page).
- - / + = move the effect one slot up or down.
- SHIFT + B3 = Delete (asks first).
- B2 (Input FX) = all input effects on or off. Off: you hear and record the input dry. The switch gives no click. On SAMPLE RECORD, the B2 label shows Input FX with a white box while you hold SHIFT and the input effects are on.
- K1 (Vol) = the input volume. You hear it on the monitor and it goes into the recording. It is the same volume as the Input strip of the Ch. Mixer.
- B1 (Back) = back to SAMPLE RECORD. When you came from the Ch. Mixer, B1 goes back to the Ch. Mixer.
The project saves the 3 input effects and the input volume. A stock MPC Sample loads and plays the input effects too.
Tip: The Knob FX, Pad FX, Flex Beat and Color Comp. do not play on the input. For a filter on the input, put one on the Input FX page. On this page, PAD FX opens the Mixer.
To Seq: record directly into the sequence
With To Seq, the MPC adds the note of the new sample to the sequence.
- Push SAMPLE RECORD.
- Push B2 to set To Seq on (white box = on).
- Use K2 to select the recording length:
- Seq: one loop from the start of the loop. The note is at the start of the loop.
- Free: the recording starts immediately and stops when you tap the pad again. The note is at the time that the recording starts.
- Tap the pad that you want to record to. After the recording, the note is in the sequence, and the pad plays at once.
- Sequence stopped: a tap on the pad starts the sequence and the recording at the start of the loop (with COUNT-IN on, after 1 bar). Without a loop, that is beat 1 of bar 1. STOP during the count-in = no recording.
- With a loop (SHIFT + PLAY, see Loop a part): the recording and the note stay in the loop.
- Record again on the same pad: the new take replaces the old notes of that pad; the automation stays. With Looper on, the new take goes on top of the old loop instead (see Looper).
- Remove a take (also a Looper take): one Undo (To Seq A01). The old notes and the old sample of the pad come back.
- On the beat: the MPC corrects the record delay of the inputs, so the take plays exactly where you played it. For the USB input, the delay of the computer comes on top: correct it in your DAW.
Tip: To Seq is tested in 4/4 and 3/4 only.
Looper
The Looper records more than one pass over the same loop. When you stop, the MPC puts all passes on top of each other in one loop.
- Push SAMPLE RECORD and set To Seq on (B2).
- Push B3 to set Looper on (white box = on).
- Set K2 to Free.
- Tap the pad and play as many passes as you want. From the second pass, you hear the passes that you already recorded.
- Tap the pad again to stop. A tap on another pad also stops the take; it does not chop it. The loop plays on without a gap, and the pad takes over at the start of the next pass. The loop starts on the start of the sequence loop, also when you started in the middle. Thus a play from the start has the full loop in pass 1.
- To add a layer, tap the same pad again, play, and tap it again to stop. You hear the old loop while you record. The new take goes on top of the old loop, at the place where you played it. One Undo removes only the last layer.
- If the sum is too loud, the sound is clipped.
- With the built-in mic and the built-in speaker, you do not hear the passes (the mic would record them again). Use headphones.
- A loop longer than 2 minutes records and merges as usual, but you do not hear the passes while you record.
- On a chopped pad, the Looper does not merge the passes, as in stock.
- A layer needs a pad with one loop of the same length (for example, the tempo did not change). Else the new take replaces the old loop.
- When you set To Seq off, Looper also goes off.
Tip: While you record, you hear the passes as they are recorded: with the input effects, but without the pad, track, submix and master effects (for example the Knob FX). You hear these effects after the stop, when the pad plays the loop. A Knob FX filter can then change the sound a lot.
Tip: With the Source USB, the delay of the computer comes on top of the record delay. Then the passes play a bit late. Correct this delay in your DAW.
STOP stays on the screen
STOP stops the sequence, but the display stays on SAMPLE RECORD, for the next take. A recording that waits ("Waiting for signal") is cancelled.
Source Rear+USB
With the Source Rear+USB, the MPC records and monitors the rear inputs and the USB audio from a computer at the same time.
- Push SAMPLE RECORD.
- Turn K1 (Source) fully to the right: Rear+USB. (It is also the last Source in the stock Input Config menu and in the Tuner.)
- Record as usual.
- The MPC adds the two inputs at full level. If both are loud at the same time, the recording can clip: turn one of them down.
- Without the SD card, the MPC starts as stock with the Source Rear.
Tuner
The Tuner shows the note of one tone: a guitar or voice on the mic, the rear input or USB audio, or a sample that the MPC plays.
- Push SHIFT + PAD 7. The Tuner opens. (In stock, this is Double Speed: see Shortcuts.)
- Turn K1 (Src) or the ENCODER to select the Source: Mic, Rear, Rear+USB (the Tuner reads only the rear inputs), USB (a computer), or Resample (what the MPC plays, also with MAIN VOLUME at 0). This is the same Source as for recording.
- Play one note. The screen shows the note (for example A3), a needle from -50 to +50 cents, and the frequency and cents. The needle is green within 3 cents. When the sound stops, the last note stays in grey.
- To tune the selected pad, turn K2 (Semi, in semitones) or K3 (Fine, in cents). This is the same tune as K1 / K2 on the Tune page of SAMPLE, with Undo. The ENCODER changes the knob that you turned last.
- Push B1 (Back), SHIFT + PAD 7 or a mode button to close the Tuner.
The note names use the MPC octaves, as KEYS and 16 Levels: C3 is MIDI note 60, so 440 Hz shows as A3 (A4 on a guitar tuner).
Tip: Play one note at a time: a chord or a drum hit often shows no stable note. A low guitar or bass string can show one octave too high, mostly at the start of the note.
Set the root note of a pad with the Tuner
- Select a pad on the SAMPLE screen or in Pad View. A pad that you play while the Tuner is open also becomes the selected pad. On SAMPLE RECORD, a pad selects the pad and does not start a recording .
- Open the Tuner. The bottom line shows the pad that gets the root note, for example "Pad T02 A05".
- Play the note:
- With the Source Resample: play the pad. The Tuner reads the sample itself.
- With a different Source (for example Rear): play the note of the sample again on the instrument. Example: you recorded an A on a guitar with Sample Record. Play the same A again.
- Push B3 (Apply). The note becomes the KEYS root note of the selected pad. For 3 seconds the bottom line shows the new and the old root note, for example "Pad T02 A05: root A3 (was C3)". Apply has no Undo step: to set it back, use SHIFT + K1 on the Tune page of SAMPLE.
Tip: Resample always gives the note of the sample. With a different Source, play the same note as in the sample. For a chord or a riff, use Resample.
Tip: To tune a pad to an instrument with K2 / K3, use the Source Resample: the other Sources hear the instrument, not the pad.
Find the key of a sample
The Tuner finds the key of a loop or a melody, for example A min, and saves it as the key of the sample. The key goes into the project and the WAV file. The MPC Sample does not use the key for the sound.
- Select a pad on the SAMPLE screen or in Pad View.
- Open the Tuner (SHIFT + PAD 7) and push B2 to go to the Key page (the Tuner page is the note and the needle). The Tuner reads the sample on layer 1 of the pad (the first 60 seconds). While it reads, the screen shows "Analysing...".
- The screen shows the key, its relative key (for example "rel. C maj"), the sample name and the key that the sample has now ("Key now"). When the sample is on more pads, the name shows "(2 pads)". When the sample has no clear key (a drum hit, noise), the screen shows "No key found".
- A key and its relative key have the same notes (for example A min and C maj). To choose the other one, turn the ENCODER or K1: right shows the relative key large, left shows the detected key large.
- Push B3 (Apply). The large key becomes the key of the sample, for all pads with that sample. With "No key found", Apply sets the key to Off. Apply has an Undo step.
- Play a different pad to read its sample. Push B2 to go back to the Tuner page.
The Tuner stays in the mode that you used last, until you switch the MPC off.
Set the key by hand: push SAMPLE, push B2 until the Tune page shows, hold SHIFT and turn K2 (Key): Off, C maj to B maj, C min to B min. One turn is one Undo step.
Auto Key: a new sample on a pad gets its key at once: a sample that you load with SAMPLE SELECT, a take of SAMPLE RECORD (one pad) and a new sample of Resample. When the sample has no clear key, its key stays Off. A sample that has a key keeps it. Loading a project or a kit does not change keys. Set Settings > Auto Key to Off to stop it.
Tip: Auto Key is its own Undo step after the load. The first Undo removes only the key; the second Undo removes the sample.
Tip: The key detection is right on most loops, but not on all. Listen before you apply, and set the key by hand when it is wrong. A drum hit can also show a key.
Sequences and tracks
A project can have up to 16 drum tracks. SampQOL OS loads all drum tracks of a project, also from an MPC One, Live or X. The pads play the current track, as on an MPC One or Live. Each track has its own 8 pad banks. Recording, NOTE REPEAT, a MIDI keyboard and Resample use the current track.
The mod always saves the project with track 1 as the current track. Thus a stock MPC Sample can open it safely.
Half Seq and Double Seq: SHIFT + PAD 2 (Half Seq) and SHIFT + PAD 3 (Double Seq) change all drum tracks of the sequence.
Select a track
- Hold PAD BANK and turn the ENCODER. Release PAD BANK to change the track.
- Or hold SHIFT + PAD BANK and push pad n: track n. While you hold them, the pads show the tracks: bright green = the current track, dim green = another track, red = a muted track, off = no track. If you turn the ENCODER, the target pad is white.
- After one turn of the ENCODER, PAD BANK alone also shows the tracks on the pads, and pad n selects track n, until you release PAD BANK. Hold only PAD BANK (no ENCODER) to see the stock bank colours on pads 1 to 8 and to select a bank.
- While you select, the track number is red. In the Track View, the track label moves to the track that you will get.
New track: select one track past the last track (for example T03+, in the Track View a new row). The MPC makes one new track with its own colour and the default settings, as a new drum track on an MPC: empty pads, no insert effects, pan in the centre, default volume and output to the Master. No setting comes from another track. One UNDO removes it.
Move a track
- Select the track that you want to move.
- Hold PAD BANK and push - (one place up) or + (one place down). The track changes places with the track next to it and stays the current track. A popup shows both tracks (or "First Track" / "Last Track": no change).
This works on all screens. Each move is one UNDO step. The pads, notes, mutes and name move with the track. A track that is named "Track n" gets the number of its new place. Names that you gave stay.
Duplicate a track
Dup. Track makes a copy of a track, without or with its events.
- In the Track View, put the cursor on the track.
- Push SHIFT + B3 (Dupl/Expl).
- Push B2 (Dup. Track). The MPC shows where the copy goes.
- B2 (Events) sets Events On or Off (it starts Off). On = the copy gets the events of all sequences (notes and pad automation).
- Push B3 (Do It). B1 (Cancel): no copy.
Track effects: when the track has track insert effects, Do It shows how many effects each choice makes. The Events choice stays.
- B3 (To Submix): the effects go one time on the first free submix (no effects, nothing goes to it), with the same settings and on/off state. The copy gets no track effects. The Out of the track and of the copy goes to that submix. On the track the effects stay, but off. Two tracks then use the CPU of one set of effects. Without a free submix, B3 does not show. When an effect cannot be copied, the display shows "FX Cannot Be Copied" and nothing changes.
- B2 (Copy FX): the copy gets its own copy of the effects.
- B1 (Cancel): no copy.
The copy is named "Track n" (n = its place). It comes directly after the track and becomes the current track. All pads, samples, pad settings, effects and routes stay. The copy shares the samples (no extra memory), is not muted and gets its own colour. One UNDO removes the copy. After To Submix, the same UNDO also puts back the effects and the Out of the track.
Tip: With To Submix, each track goes into the effects after its track volume. A reverb, delay or EQ sounds the same. A compressor or distortion sounds the same only with the track volume at 0 dB.
Tip: With 16 tracks, or on a track that is not a drum track, B2 does not show. Line 1 of the question shows why.
Explode
Explode puts pads with notes on their own new tracks.
- In the Track View, put the cursor on the track.
- Push SHIFT + B3 (Dupl/Expl).
- Push B3 (Explode). When Explode is not possible, the MPC shows why and B3 does not show.
- The MPC shows the number of pads and the new tracks. Push B3 (Do It). B1 (Cancel): no Explode.
- Each pad with notes in the current sequence of the cursor track gets a new track, directly after the track. Pads in the same Mute Group go together to one track. The old track is muted.
- A pad with Out set to Master goes to Track, so the track strip, volume, mute and solo work on it. A pad with Out set to a submix or another output keeps it.
- The new tracks get the RT Swing of the old track in each sequence.
- A track behind them that is named "Track n" gets the number of its new place. Names that you gave stay.
- One UNDO removes the full Explode, also submix effects. Explode works only in the Track View, with the sequence stopped.
Track effects: when the track has track insert effects, step 4 shows how many effects each choice makes, and B3 is not Do It:
- B3 (To Submix): the effects go one time on the first free submix (no effects, nothing goes to it), with the same settings and on/off state. The Out of the new tracks goes to that submix. On the old track the effects stay, but off. This uses much less CPU. Without a free submix, B3 does not show. When an effect cannot be copied, the display shows "FX Cannot Be Copied" and nothing changes.
- B2 (Copy FX): each new track gets a copy of the effects.
- B1 (Cancel): no Explode.
Tip: With To Submix, each track goes into the effects after its track volume. A reverb, delay or EQ sounds the same. A compressor or distortion sounds the same only with the track volume at 0 dB.
Tip: Mute Targets (one pad stops another, from an MPC One, Live or X project) work only on one track. Put the two pads in the same Mute Group before Explode, so they go to one track.
Delete a track
In the Track View, push SHIFT + B1 (Delete). After a question, this deletes the cursor track, with its notes in all sequences. It works only with the sequence stopped. The last track always stays. A track behind it that is named "Track n" gets the number of its new place. One UNDO puts all back.
Copy a pad to another track
- Select the source pad. Hold SHIFT + ERASE (COPY) and push the destination pads, as in stock.
- While you hold COPY, turn the ENCODER to select the destination track, for example "Copy from A01 to Track 04 A02".
- Release. The MPC goes to the destination track.
Only the sample is copied (shared), not the notes. If a destination pad has a sample, the MPC asks first ("COPY PAD"):
- B1 = Cancel.
- B2 = Swap: the two pads change places, also between two tracks. Only for one destination pad. The notes stay on their pads: a note on A01 plays the sample that was on the other pad. You stay on the source track. One UNDO puts the pads back.
- B3 = Replace: the sample goes on the destination pads.
Tip: A Swap between two tracks needs one pad without a sample on one of the two tracks. When all 128 pads of both tracks have a sample (as two copies of the factory demo kit), B2 Swap does not show.
Select a sequence from the SAMPLE screen
Hold SEQ and push pad n: sequence n of the current pad bank. You stay on the SAMPLE screen. When the sequence plays, it changes at the end of the loop. SEQ alone opens the SEQ screen, as in stock.
Or hold SEQ and turn the ENCODER, and release SEQ. This also works in Step Edit, on all Mixer pages, and on the stock Pad FX and Flex Beat screens.
While you hold SEQ, the pads show the sequences of the pad bank: green = current, yellow = with events, off = empty, red = waits for the end of the loop.
Tip: On the Pad FX or Flex Beat screen, you can change the sequence and play the effects with the pads and KNOB FX: one screen for a live performance.
Select a sequence with MIDI Program Change
An external MIDI device can select a sequence with a MIDI Program Change. Program 1 selects sequence A01, program 2 selects A02, and so on.
- Push and hold SHIFT and push PAD 8 – MIDI CONFIG.
- Set Receive Program Change to Sequence.
- Set MIDI In Channel to the channel of your MIDI device, or to All.
The MPC uses only a Program Change on the MIDI In Channel (All = each channel). Stock uses a Program Change on each channel, also with one channel set.
Select grid
While you select a track or a sequence, the display shows a 4x4 grid in pad order (pad 1 is bottom left), with the number and name in each cell.
- Tracks: hold SHIFT + PAD BANK for 0.3 seconds, or hold PAD BANK and turn the ENCODER, until you release PAD BANK. With SHIFT + PAD BANK + a pad, the grid shows at once. A quick tap of SHIFT + PAD BANK goes one pad bank back and shows no grid.
- Sequences: hold SEQ for 0.3 seconds, or hold SEQ and turn the ENCODER: the 16 sequences of the pad bank of the sequence that you will get. After the grid, the release of SEQ does not open the SEQ screen.
- A thick white frame shows the track or sequence that you will get, a thin white frame the current one, a thick red frame the sequence that waits for the end of the loop. A dark cell is a muted track or an unused sequence. A new track shows as + with "New track".
- Set Settings > Track Grid on Screen and Seq Grid on Screen to On, Off or Toggle. With Toggle, push B2 to set the grid on or off (B2 is white when the grid is on). The MPC keeps this choice.
Name a sequence
- On the SEQ screen, push SHIFT + B3 (Rename).
- Change the name as in stock, or push SHIFT + B3 (Preset) and select a name: Intro, Verse, Chorus, Bridge, Drop, Outro and more.
- Push B3 (Do It!). UNDO works.
A sequence gets the name "Sequence 08" when it gets its first events, as in stock. The SEQ screen shows the name in grey next to "Seq A08". Song mode shows "A01 Intro", or only "A01" for a default name.
In SEQ mode, the pad of the current sequence is green, a sequence with events is yellow, and an empty sequence is off.
Clear a song
Remove all sequences from the song at once. In stock, B2 (Remove) removes only one row.
- Push SHIFT + PAD 12 to open Song mode.
- Push SHIFT + B2 (Clear All). The song is empty. UNDO gets it back.
Tip: Stop the song first. While the song plays or when it is empty, Clear All is grey.
Quick Add in Song mode
With Settings > Song Pads = Quick Add, a pad inserts its sequence at once after the selected row, without B3. Pad 1, pad 1, pad 2 = A01, A01, A02. A pad of an empty sequence inserts it too ("(unused)"), as B3 does: B2 or UNDO removes it. While the song plays, a pad does not insert.
Tip: Each row shows the tempo that plays. With BPM: GBL on the SEQ screen, this is the global tempo on all rows. Stock shows the tempo of the sequence.
Record mutes
- Set SEQ RECORD on and play the sequence (PLAY).
- Push MUTE for Mute mode.
- Push a pad to mute or unmute it. The MPC records each push. UNMUTE ALL (SHIFT + MUTE) is also recorded.
- The mutes play again in each loop, only in this sequence.
- The timing is the exact time of the push. Time Correct does not change it.
- Recorded mutes have priority over a live push.
Tip: UNMUTE ALL also unmutes all muted tracks. Without a recording, it is one undo step: UNDO brings all the pad mutes and track mutes back. During a recording, UNDO removes the recorded pass, and the pads keep the mute state that they have then.
Tip: For a sequence that starts with a pad muted, set the pad to the correct state and record one push from the start.
Erase mutes: in Mute mode, hold ERASE and push a pad. Push B3 (Do It!). Only the mutes of that pad go.
Mute Type
Settings > Mute Type sets how a mute sounds: pad mutes (Mute mode, Pad Mixer, a pad that the Solo of another pad mutes) and track mutes (Track Mute, Ch. Mixer, Explode).
- Audio: a pad stops at once. A track fades out in 5 ms, without a click. A MIDI note that sounds gets its note-off when you mute.
- Event: only the new notes stop; the notes that sound play to their end. A muted pad then also does not stop the other pads of its mute group.
- A muted track or pad sends no MIDI notes, with both types.
- A track that you muted with the other type stays muted. One push unmutes it.
Tip: A pad with Out set to a submix or an output does not fade with an Audio track mute: its sound stops at once, with a click. Use Event, or set Out to Track.
Track Mute
Mute a whole track with the pads.
- Hold MUTE for 0.7 seconds, or push PAD BANK + MUTE. The 16 pads are the 16 tracks.
- Push a pad to mute or unmute that track: green = plays, red = muted, off = no track. (In pad Mute mode, a pad that plays is yellow.)
- With SEQ RECORD and PLAY, the MPC records each push, as pad mutes. This works for every track, also for a track that is not the current track, and on the SAMPLE screen and the SEQ screen. Track Mute stays on when the recording starts and stops.
- To select another sequence, hold SEQ and push a pad (the pads show the sequences while you hold SEQ). Track Mute stays on. During play, the next sequence starts at the end of the loop.
- To stop Track Mute, push MUTE or SAMPLE, or open another screen.
Erase track automation: in Track Mute, hold ERASE and push a pad. See Erase all automation of a track.
Tip: SHIFT + MUTE unmutes all tracks, in Track Mute and on the other screens. Without a recording, it is one undo step.
Tip: Track Mute and Mute (B3) on the Ch. Mixer are one mute. The Ch. Mixer also shows a recorded track mute that plays.
Track mutes per sequence
Each sequence keeps its own track mutes, as on the MPC Live: mute the track in each sequence where it must be quiet. Pad mutes are the same for all sequences. The project saves them. A project with one set of track mutes uses this set in each sequence.
- Copy a sequence to a new sequence (for example Seq 2 and Seq 3). The copy becomes the current sequence.
- Select each sequence and mute other tracks there. In Track Mute, hold SEQ and push a pad to go to a sequence without leaving Track Mute.
- Use the sequences as parts of a song, or in Song mode.
When you export the song to a sequence (Song > Export > Sequence), each part start gets a track-mute event for each track, as a recorded track mute. A stock MPC Sample does not play these track mutes: all tracks sound there.
The new sequence also keeps the RT Swing. A sequence holds one RT Swing per track, so each track gets the RT Swing of the first part of the song.
Tip: If later parts use a different RT Swing, set it again on the new sequence (SEQ, K3).
Tip: UNDO of a track mute changes the sequence where you made the mute, also when another sequence is selected. This is also true for the mute that Explode gives the source track.
MIDI out: a track plays an external synth
A track can send its notes on its own MIDI channel. The pads of that track then send the note that you hear: a Scale, Tune or KEYS note goes out as the real note. One track plays one part of an external synth.
Connect the synth:
- Connect a computer or iPad with a USB-C cable to USB-C, or a synth with a 1/8" (3.5 mm) TRS to 5-pin MIDI DIN cable (not included) to MIDI OUT.
- In MIDI Config (SHIFT + PAD 8), set MIDI Port to USB or External.
Set the MIDI channel of a track:
- Select the track.
- Push PAD FX, then B1 until the Track page shows.
- Hold SHIFT and turn K3 (MIDI). The track uses the setting at
once:
- Off: the track sends no MIDI notes.
- Glob. (Global, default): the track sends as in stock, with the MIDI Out Channel and Pad MIDI Out of MIDI Config. A 16 LEVELS pad sends its source note, one note per press (also with a Scale Chord).
- Ch 1 to Ch 16: the track sends on this channel.
Pad MIDI Out in MIDI Config also sets which pads of a track with its own channel send: Always (all pads), When Empty (only pads with no sample) or Never. The track grid shows the channel, for example Ch 3. The project saves the setting. A new track starts with Glob. The MIDI setting has no undo.
Tip: To play an external synth from one pad, set Pad MIDI Out to When Empty and use an empty pad. The pads with a sample then play only their sample.
Tip: You can also set the channel on the Ch. Mixer: select the track strip, hold SHIFT and turn K3 (MIDI). This sets more tracks without leaving the mixer.
Tip: Play more synths from one MIDI OUT: give each synth its own channel and connect them in a chain (MIDI THRU to MIDI IN), or use a MIDI thru box. Set the tracks that must not play a synth to Off. MIDI Port is for all tracks: all send on USB or all on External.
The notes on MIDI out:
- A normal pad sends its own note. A KEYS key sends its own note. A chord and the Arp send all their tones.
- A 16 LEVELS Scale or Tune pad sends the KEYS root note of the pad (Off = C3, note 60) plus the Tune. Example: Scale, Key C, Major, root Off: PAD 1, PAD 3 and PAD 5 send C3, E3 and G3.
- Each pad stops only its own notes. Two held pads on the same note and channel are one note on the synth (a MIDI limit): the second pad starts it again, and it stops with the last pad.
- The recording keeps the length of each pad, also when pads overlap.
- STOP while the sequence plays stops all notes. When the sequence does not play, a held pad plays until you release it.
Tip: Give each synth part its own track with its own channel. On a new track or a pad with no sample, you hear only the synth. Scale, Tune and KEYS also work on a pad with no sample.
Tip: Use a source pad that the sequence does not play. A recorded note of the source pad also stops the live notes of that pad (as in stock).
Step Edit
Step Edit has two views:
- Pad View (SHIFT + SAMPLE): one pad on each row, the steps of one page.
- Track View (SHIFT + SEQ): one drum track on each row, 1 to 8 bars.
The two views use the same controls where possible. While you hold SHIFT, the buttons show their SHIFT function.
Tip: While the KNOB FX bar shows, B1 and B2 do the stock Step Edit functions, and B3 is Knob FX Bypass (with Knob FX B3 Bypass Off: the stock Erase). While the NOTE REPEAT bar shows, they set the Note Repeat rate. The labels at the top show these functions.
To select another sequence, hold SEQ and push a pad or turn the ENCODER (see Select a sequence). You stay in Step Edit.
A new note (a step pad, or a pad with SEQ RECORD on and the sequence stopped) is one step long, also on a One Shot pad. With SEQ RECORD and PLAY, the note is as long as you hold the pad, as in stock. FULL LEVEL (SHIFT + PAD 1) works in both views, also with Steps on.
Note Repeat works in both views (in stock, not in Step Edit): with SEQ RECORD and PLAY, hold NOTE REPEAT and a pad. The pad repeats at the Time Correct value, not the zoom. B1-B3 select the rate, as in stock. K1-K3 and the ENCODER work on the view. With Steps on, the pads play while you hold NOTE REPEAT: they do not set steps.
Pad View
The Pad View shows 1 to 16 pads (default 8, see Settings > Pad View Rows and Fader in Step Edit) with 16 steps. Each note is a block: the width is the length, the colour is the velocity (light yellow = soft, red = hard). A red line shows the end of the sequence.
- ENCODER: moves the cursor one step. SHIFT + ENCODER selects the row. - / + = previous / next page.
Tip: With 12 or 6 rows, the last window ends at pad 16, so two windows show some of the same pads (12 rows: A01-A12 and A05-A16). The window changes only when the cursor goes off the screen. SHIFT + ENCODER to the right always goes down the screen, also with Pad View Order 1 Bottom.
Tip: After Resample, Project, Time Correct, the FADER menu, MIDI Config, PAD FX or SAMPLE SELECT, Step Edit comes back with the same cursor, page, Steps and selection.
Steps: add notes with the pads
- Push SHIFT + B2 to set Steps on (off when the Pad View opens). The 16 pads are the 16 steps of the page. A lit pad has a note.
- Tap an empty step to add a note, a set step to remove it (no sound).
- To select another row, hold SAMPLE and push a pad (no sound; Steps stays on). While you hold SAMPLE, the pads light as on the SAMPLE screen. A short push of SAMPLE alone opens the SAMPLE screen. Hold and release SAMPLE without a pad to stay in the Pad View.
- A tap on a step after the end of the sequence does nothing.
- The 16 steps are 1/16, one bar (or the grid of Settings > Pad View Grid). To zoom, see Zoom in the Pad View.
Play the pads (Steps off): with Steps off (Play), the pads play, with the colours of the SAMPLE screen. The pad that you hit becomes the row. With SEQ RECORD on and the sequence stopped, a pad hit adds the note at the cursor, and the cursor goes one step on.
Edit notes with the knobs
- K1 (Nudge) moves the notes in whole steps, inside the page (with SHIFT: fine, in ticks, up to one step to each side). With Nudge in Fader Overrides, the FADER moves fine. K2 (Length) sets the length (1 tick to one page; it shows the longest note). K3 (Velocity, 0 to 127; it shows the first note) sets the velocity.
- Without a held pad, the knobs edit the selection, or the note at the cursor, in Steps and in Play. A note off the grid belongs to the cell where you see it.
- The MPC writes the change after a half second. Each write is one UNDO step. The notes stay under the knobs until you turn the ENCODER or use another control: you can turn again after a rest.
- Rec Quantize on (SHIFT + PAD 10): K1 puts the first note on the grid, and K2 makes the length a whole number of grid steps. With SHIFT (fine), the notes move freely.
Copy, paste and erase notes
- B1 (Copy) copies the notes of the selection, or of the cell at the cursor, with their velocity, length and place in the step (no automation or pad pressure). Move the cursor and push B3 (Paste): the first step goes on the cursor step, the top pad on the cursor row. When you copied all pads (SHIFT + push the ENCODER), each note goes on its own pad. With nothing to copy, the MPC shows "Nothing to copy". If there are notes, the MPC asks Merge or Replace. Paste on the place that you copied from does nothing while the notes are still there. You can paste in another sequence.
- SHIFT + B1 (Cut) copies the notes and removes them at once. Then Paste as after Copy. B1 (Cancel) does not put the notes back: push UNDO. The cut and the paste are each one UNDO step.
- SHIFT + B3 works as B3 (Duplicate, or Paste after Copy).
- ERASE alone (push and release, no pad) clears the selection, the note at the cursor, or the steps that you hold. One UNDO puts all back.
- A small white + on a note: two or more notes of this pad start in this cell, for example a double note at the loop end after a recording. ERASE at the cursor then clears one note: the note that is farthest from the Time Correct grid (also when you zoom). The note that is most on time stays. Push ERASE again for the next note. A selection or the held steps clear all notes.
- ERASE + pad: B2 (Page) erases the notes and automation of that pad on this page. B3 (Do It!) erases the full sequence.
Zoom in the Pad View
- Steps on: SHIFT + K3 zooms the steps from Bar to 1/64T (at 1/32 the 16 pads are a half bar, at 1/4 four bars). Bar shows 16 bars: the pads show where the notes are, and a tap adds no note.
- The zoom does not change your Time Correct (Rec Quantize): your value comes back when you set Steps off, go to the Track View, close Step Edit or save the project.
- Steps off: SHIFT + K3 (Bars) zooms the view to 1, 2, 4 or 8 bars, as in the Track View. The grid does not change. The controls work on the columns that you see, and K1 and K2 in grid steps.
Rec Quantize grid and strength: push SHIFT + PAD 10. A popup shows On or Off.
- Turn K3 (Q) to select the grid (Bar to 1/64T).
- Turn K2 (Q Str) to set the strength, 0 to 100. At 100 a recorded note goes on the grid. At 50 it moves half the way to the grid, so you keep some of your own timing. At 0 it stays where you played it.
- Push B3 (Do It!) to set both, or B1 (Cancel).
The ENCODER changes the knob that you turned last: one strength step or one grid value. Without a turn, the popup closes after 2 seconds. The popup sets your own value; the zoom stays.
Tip: The strength is saved with the project. A new project starts at 100. Stock has no strength control.
Tip: The strength is only for recording. Time Correct (SHIFT + PAD 14, Do It!) always puts the notes on the grid (100).
Track View
The Track View shows the drum tracks of the sequence. Each track has its own colour, the same as in the Ch. Mixer. The notes of the cursor track are bright, the others are dimmed. A red line shows the end of the sequence, as in the Pad View.
- You see 4 bars. SHIFT + K3 (Bars) zooms: 1, 2, 4 or 8 bars. A column is 1/16 of the window. - / + = next or previous bars.
- ENCODER: moves the cursor one column. SHIFT + ENCODER goes to another track. That track also becomes the current track.
- The pads play the cursor track, with the colours of the SAMPLE screen.
- K1 (Nudge), K2 (Length), K3 (Velocity), the FADER and Rec Quantize work as in the Pad View, inside the window you see. Nudge and Length use whole grid steps (the Time Correct value, for example 1/16). With SHIFT: fine, in ticks (up to one grid step for Nudge).
- B1 (Copy) and B3 (Paste) work as in the Pad View, with columns and tracks for steps and pads.
- Cut: there is no Cut button (SHIFT + B1 is Delete). Push B1 (Copy), then ERASE (the copy stays), then Paste. You can paste on the place that you cut from.
- ERASE alone (push and release, no pad) clears the notes in the selection at once, with a short message (not for one note), and their pad pressure. Other automation stays.
- SHIFT + B1 (Delete): see Delete a track.
- Row labels, row count and order: Settings > Track View Labels, Track View Rows and Track View Order. With 12 or 16 rows, the cursor track has the same height as the other tracks.
Selection
The selection works the same in both views.
- Put the cursor on the first cell and push the ENCODER (yellow frame).
- Turn the ENCODER (with SHIFT: the rows). The selection (light blue) is the rectangle from the first cell to the cursor, also past the screen (a small white arrow).
- The selection stays. Another button or knob (also ERASE) ends the yellow frame: then the ENCODER moves the cursor again.
- Push the ENCODER again for no selection.
- B2 (Sel. Row): add the cursor row to the selection, or remove it. With no selection, this selects the whole row over the full sequence.
- SHIFT + push the ENCODER selects all rows: all pads of the pad bank, or all tracks. With no selection, it selects them over the full sequence. Push it again for no selection.
- With no selection, the knobs and buttons use only the cursor cell.
- Notes move as one block: when one note would land on the same note, no note moves.
- B3 (Duplicate) pastes a copy of the selection directly after it, in one push. The selection moves to the new part, so the next push goes on. With no selection, the new cell becomes the selection. After Copy, B1 = Cancel and B3 = Paste (once); then Copy and Duplicate come back.
- One Copy or Duplicate takes up to 8192 notes. With more, the display shows Too many notes and nothing is copied.
- One UNDO puts back a clear, a move or a paste.
Loop a part
- SHIFT + PLAY plays the bars of the selection in a loop. The loop stays on other screens, after STOP and without a selection: SHIFT + PLAY plays it again from its first bar. While the sequence plays, SHIFT + PLAY starts it again at the loop.
- PLAY plays from bar 1 and ends the loop, as do STOP two times and another sequence in Step Edit.
- To record a part again and again: STOP after each take, then SEQ RECORD and SHIFT + PLAY.
- With no loop and no selection, SHIFT + PLAY plays from the playhead, as stock CONTINUE. Set Settings Shift+Play Starts to Cursor to start at the cursor. While the sequence plays, it starts again at the cursor.
Automate: write a fade
Automate writes a fade of the track volume or a track filter into the selection (or the cursor cell) of the Track View.
- Make a selection in the Track View.
- Push SHIFT + B2 (Automate):
- K1 = Start %, K2 = End % (100 % = the current value, 0 % = silent).
- K3 = Volume, LP Filter or HP Filter.
- SHIFT + K3 = Curve: Linear, Log (equal dB steps, natural fade-out) or S-Curve.
- Push B3 (Do It!), or B1 (Cancel).
- A filter fade needs the filter as an insert. If the track has none, the MPC adds it to a free insert slot at Do It!. Turning K1-K3 adds nothing. If all 4 slots are full, it writes nothing.
- A filter on many tracks: if 2 or more tracks need a new
filter, the window shows "N new inserts". Do It! then asks where the
filter goes:
- B2 (Track FX): one filter on each track.
- B3 (Submix n): one filter on a submix. If all the tracks go to the master, the MPC uses the first free submix and sends the Out of the tracks to it. If all the tracks go to the same submix, the filter goes on that submix. The window names the other tracks on that submix: they get the filter too.
- If the tracks go to different outputs, or no submix is free, only Track FX is possible. This is also so if their submix has no filter of that type and all its 4 insert slots are full: the window says "Submix n: inserts full". Free a slot in the Mixer (PAD FX) to use it.
- If a track has its own filter of that type with points in the selection, the window shows it in yellow (e.g. "T03 has points"). Track FX replaces those points. Submix keeps them: that track then goes through 2 filters there.
- If you select all the tracks of a submix (2 or more) and that submix has the filter already, Do It! writes the fade on that submix, with no question. Replace and Remove then also see the fade on that submix. One track always gets its own filter.
- One UNDO removes the full fade: the filters it added, the Out changes and the fade points.
- Master fade: select all tracks (SHIFT + push the ENCODER) and select Volume.
- If there is volume automation in the selection, B3 shows Replace.
- One UNDO removes the fade and gives the old volume back, also when you stopped the sequence in the middle of the fade.
- A fade belongs to the sequence where you write it. The other sequences play your own value (Mixer, FADER, Pad Mix); 100 % in the fade is that value. A change of the volume or the filter in a sequence without the fade is your new value for all of them. UNDO of a volume change also sets that value back.
- When you stop in the sequence with the fade, you hear the start of the fade. Before and after the selection, you hear your own value.
Tip: Write a volume fade while the sequence is stopped. If you write it while the sequence plays, UNDO keeps the volume of the STOP. Then set the volume again in the Mixer.
Tip: Set the sequence length before you write a fade to the end of the sequence. If you make the sequence longer after a fade-out, you hear your own value after the old end: write the fade again over the new length.
Remove a fade
- Make a selection in the Track View and push SHIFT + B2 (Automate).
- Select the target with K3.
- Push B2 (Remove): the MPC removes the fade points of that target in the selection, on the selected tracks.
- To remove all fades (Volume, LP Filter and HP Filter) of the selected tracks in this sequence, hold SHIFT and push B2 (Remove All). The selection does not matter for Remove All. Release SHIFT after you open the window, then push it again: a SHIFT that you still hold from SHIFT + B2 does not count.
- B2 shows only when there is something to remove.
- The filter insert stays on the track. Only its fade goes.
- In the removed part, you hear the value before it. When no fade point is left in the sequence, you hear your own value (Mixer, FADER, Pad Mix).
- One UNDO brings back all that Remove or Remove All removed.
Fader in Step Edit
Set what the fader does in the Pad View and the Track View: SHIFT + PAD 9, then B2 (Overrides), line Pad / Track View (see Fader Overrides):
- Nudge (as in stock): the fader moves the note.
- Fader Menu: the fader does what you set in the FADER menu.
- Zoom (default): the fader sets the rows that the Pad View and the Track View show. Fader at the bottom = 16 rows, at the top = 1 row. The position is the zoom: there is no takeover. The view keeps the rows (Settings > Pad View Rows / Track View Rows).
Track Volume in the FADER menu (stock: "Kit Volume"): see Track Volume on the FADER.
Mixer
Push PAD FX to open the Mixer, from every mode. Tap PAD FX again to go back. For the stock Pad FX and Flex Beat screens, see Shortcuts.
The Mixer opens on the page that you saw last. To open it always on the pad inserts (Pad inserts) or on the Ch. Mixer, set Settings > Mixer Opens On.
Insert pages
- B1 steps through Pad > Track > Submix > Master, in the order of the sound. B2 opens the mixers. As in stock, B1 or B2 from the other group always opens the first page of its group.
- Submix shows the submix of the current pad (or its track), else the last submix.
- Turn the ENCODER to select one of the 4 insert slots.
- To select a pad, track or submix: hold PAD FX and push a pad (no sound). The pads show the colours of the SAMPLE screen (Pad), of SHIFT + PAD BANK (Track), or purple (Submix).
- Or hold PAD FX and turn the ENCODER: the previous or next pad (all 128, the pad bank follows), track or submix. One step past the last track (Track nn+) makes a new track when you release PAD FX, as with PAD BANK + ENCODER.
- PAD BANK + ENCODER (track) and SEQ + ENCODER (sequence) also work in the Mixer.
- K1 = volume. K3 (Out) = where the sound goes: Track, Submix 1-8 or Master. On the Pad page, Trk 1 = the track of the pad (track 1). With 16 USB Outputs On, a track and a submix can also go to a USB output.
- K2 (Pad Grp, Trk Grp or Sub Grp) = the mute group. See Mute groups.
| Control | Empty slot | Slot with an effect |
|---|---|---|
| B3 or ENCODER push | Insert: opens the Insert FX list | B3 = Edit: opens the effect page. ENCODER push = effect on/off |
| - / + | Nothing | Moves the effect one slot up / down |
| SHIFT + B3 | Nothing | Delete (asks first). The automation of the slot goes too (knobs and on/off), in all sequences. One UNDO puts all of it back |
Insert FX list: 6 categories (Delay/Reverb, EQ/Filter, Dynamics, Harmonic, Modulation, Vintage), with the effects that are On in Insert FX List. Push the ENCODER to open a category or to load the effect. A track or submix also has Color Comp., and a track, submix or the master also Kill EQ. Only here, not in Knob FX: Mother Ducker, Mother Ducker Input, AIR Compressor and AIR Stereo Width. A load is one UNDO step. REDO puts the effect back with the values of the load, for example AIR Compressor neutral.
EQ row: on the Pad page (with Settings > Pad EQ On), the row EQ under the 4 slots opens the EQ page of the pad: select it and push B3 (Edit) or the ENCODER. From the EQ page, PAD FX always opens the Pad page with EQ selected, also with Settings > Mixer Opens On.
Effect page: shows the 6 main parameters. K1–K3 (SHIFT: the second layer) change them, with the Parameter Takeover of MIDI Config. B3 = Bypass. B1 or PAD FX = back.
- LP Filter, HP Filter and BP Filter show the filter curve with the cutoff, and a live spectrum after the filter.
- The Limiter shows three meters: In (after Gain), GR (gain reduction) and Out. With Bypass on, they stay at zero.
To record the knobs of an effect on a pad, a track or a submix as automation:
- Push SEQ RECORD, then PLAY.
- After the count-in, turn the knobs on the effect page.
- Push STOP. The sequence plays the knob moves.
One undo removes the full recording. Outside a recording, the knobs have no undo.
Tip: An effect on the master records no automation.
MIDI channel of a track: on the Track page, SHIFT + K3 (MIDI). See MIDI out.
UNDO and REDO work for the actions in the Mixer. With SEQ RECORD and PLAY, the MPC records effect on/off and the volume.
Tip: A track insert hears a pad only when the pad goes to its track (K3 = Track). With Submix 1, the pad skips the track.
Rename a track, submix or pad
- Push PAD FX to open the Mixer.
- Go to the Pad, Track or Submix page.
- Push SHIFT + B1 (Rename).
- Change the name, or push SHIFT + B3 (Preset) for a list (B2 Abbreviate gives short names: Drm, Vox, Rvb).
- K1 sets the colour of a track or pad.
- Push B3 (Do It!) to save.
The project keeps a pad name. An empty name gives the pad its sample name again.
Mute groups
K2 on the Pad, Track and Submix pages of the Mixer sets the mute group (- = Off). On the Ch. Mixer and the Pad Mixer, SHIFT + K2 sets the group of the selected strip. Pads, tracks and submixes have separate groups.
- Pad (Pad Grp): the stock pad Mute Grp (Off, 1-32): a choke. A pad stops the other pads of its group. One turn of K2 is one UNDO step.
- Track (Trk Grp): Off or 1-8. When you mute or unmute a track, the other tracks of its group get the same mute. This works in Track Mute and with Mute on the Ch. Mixer. One UNDO puts all of them back.
- Submix (Sub Grp): Off or 1-8. Mute of a submix on the Ch. Mixer also mutes or unmutes the other submixes of its group.
Tip: Track Mute shows the group of a track in its cell, for example G1. Solo does not follow the group. With SEQ RECORD and PLAY, the MPC records the mute of each track of the group.
Master
The master has 4 slots with Pad FX, Flex Beat, Color Comp. and Knob FX, as in stock. The Knob FX slot shows the effect of FX Select, for example "(Knob FX) LP Filter".
-
Remove: select the slot, push SHIFT + B3, then B3 (Remove). This saves CPU. UNDO puts it back.
-
Hidden: in the same window, set B2 (Use Hidden) on. The effect keeps working, but it frees its slot. A grey line under slot 4 shows the hidden effects. The COMPRESSOR screen shows "Hidden" when the master Color Comp. is hidden. The screen of a hidden effect opens as usual.
-
Back to the master: select an empty slot and push B3 (Insert). The hidden effects are at the top of the list, for example "Flex Beat (Hidden)". Push B3 (Select): the effect goes to this slot, with its settings.
-
Pad FX, Flex Beat and Color Comp. can move to another slot (- / +). Knob FX stays on its slot.
-
Color Comp. Off = Bypass on the COMPRESSOR screen.
-
Edit (B3) opens the stock screen of the effect. PAD FX goes back to the Mixer, on the same slot.
-
When you open the screen of a removed effect, the MPC asks to put it back (B2 = Hidden, B3 = Insert; with 4 full slots: "MASTER FULL").
Channel Mixer and Pad Mixer
Push B2: Ch. Mixer, then Pad Mixer. Each mixer shows 8 strips per page. Turn the ENCODER to select a strip and to see more strips.
- Ch. Mixer: the tracks with notes, the submixes in use, and the master. The strip Input is always at the far left. See below.
- Pad Mixer: the pads of the current track with a sample and notes. Play a pad to select its strip.
- A track strip shows the colour of its track. A pad strip shows the colour that you give the pad with Rename. A pad without its own colour is white.
- Each strip has a stereo meter (red above 0 dB). A peak line stays until you push SHIFT + ENCODER (all strips).
- K1 = volume, K2 = pan (L50 to C to R50), K3 = output.
- SHIFT + K2 = the mute group of the selected strip: Pad Grp, Trk Grp or Sub Grp (- = Off), as K2 on the insert page. Hold SHIFT to see the group. The master strip has no group: there, SHIFT + K2 is also pan. See Mute groups.
- SHIFT + K3 on a track strip = its MIDI channel (Off, Glob., Ch 1 to Ch 16), as on the Track page. See MIDI out. On the other strips, SHIFT + K3 is the output.
- SHIFT + B1 (Inserts) opens the insert page of the selected strip. B2 goes back to the mixers.
- The FADER also sets the volume of the selected strip, with the Fader Takeover of MIDI Config. When the FADER menu is Off, the FADER does nothing.
- Volume with the ENCODER: push the ENCODER (yellow frame), turn it, and push it again to select strips again.
- B3 = Mute, SHIFT + B3 = Solo. SHIFT + B2 (Clear M/S) turns off all mutes and solos of the page.
- Mute on a track strip is Track Mute (see Track Mute).
- Solo on a submix solos the tracks and pads that go to that submix.
- ERASE + K1, K2, FADER or B3 erases the recorded automation of the selected strip. See Erase automation in the mixers.
Input strip in the Ch. Mixer
The far left strip of the Ch. Mixer is the input of SAMPLE RECORD.
- K1, the FADER or the ENCODER (push, turn) = the input volume. You hear it on the monitor and it goes into the recording. It is the same volume as K1 on the Input FX page.
- The meter shows the input after the input effects and the volume: what you record.
- The strip is grey while you do not hear the input (Monitor on SAMPLE RECORD). Monitor On makes you hear it on every screen.
- SHIFT + B1 (Inserts) opens SAMPLE RECORD with the Input FX page. B1 (Back) on that page comes back to the Ch. Mixer.
- The input has no pan, output, mute or solo. Set the monitor on SAMPLE RECORD.
16 USB outputs
The MPC sends tracks and submixes to a computer on 16 more USB audio channels. In your DAW, the MPC shows 18 inputs: USB 1-2 is the main mix, USB 3 to USB 18 are the tracks and submixes that you send there.
- Open Settings and set 16 USB Outputs to On. The MPC shows "Restart the MPC to apply." and that each boot-up takes a few seconds more while the setting is On. Push B3 (OK).
- Turn the MPC off and on again.
- Push PAD FX. Push B1 until the Track or Submix page shows. Or select a track or submix strip on the Ch. Mixer.
- Turn K3 (Out). After Master come USB 3 to USB 18 (one channel, mono), then U3/4 to U17/18 (a stereo pair).
- A track or submix on a USB output is not in the main mix. You do not hear it on the MPC phones or speaker, as an output on an MPC Live.
- Two tracks on the same USB output play together on it. A + after the output (for example USB 5+) shows that another track or submix also plays on it. A stereo pair uses two mono outputs: U3/4 = USB 3 + USB 4. So you have 8 stereo pairs, or 16 mono outputs, or a mix of the two.
- A mono output gets the left and the right channel mixed, at half level each.
- A pad has no USB output. Send the pad to its track or to a submix, and send that track or submix to USB.
- MAIN VOLUME does not change the USB outputs.
Tip: The MPC needs a few seconds more to start with 16 USB Outputs On. If your computer does not show 18 inputs, connect the USB cable again.
Tip: With 16 USB Outputs Off, or on a stock MPC Sample, a project with USB outputs shows "Unsupported Outputs" when it loads. RESOLVE sets these outputs to the Master.
Tip: If the MPC restarts while SD Card Access is open, it starts with 2 USB channels and the default settings. Turn the MPC off and on again to get the 16 USB outputs and your settings back.
Tip: The USB audio to the computer (all USB channels, also USB 1-2 with 16 USB Outputs Off) is about 5 ms later than the MPC outputs. This prevents short gaps of silence. Your DAW does not know this delay. If a recording from the MPC is late in the DAW, set a recording offset of about 5 ms there.
Track Volume on the FADER
In the FADER menu, Track Volume sets the volume of the current track. It is the same volume as K1 on the track strip of the Ch. Mixer.
- Push SHIFT + PAD 9. Select Track Volume with the ENCODER and push it. If the fader is off, push B3. Push B1 (Back).
- Move the FADER. The volume of the current track changes.
- UNDO does not undo a FADER move (as stock Kit Volume).
- With SEQ RECORD and PLAY, the MPC records the volume. Hold ERASE and move the FADER to erase it (see Erasing automation).
Tip: Track Volume changes only the pads with their output on the track. A pad with its output on a submix or the master does not follow it.
Effects
The effects that SampQOL OS adds or changes. You put an insert effect on a pad, track, submix or the master in the Mixer (see Insert pages).
Knob FX on all pads
The Knob FX is on the master. Every pad on every track plays through it.
- K1-K3 and SHIFT + K1-K3 work as in stock. See also Change the Knob FX on any screen.
- In FX Select (SHIFT + KNOB FX), all pads are lit and there is no B2 (All Pads). B3 (Bypass) works as in stock.
- The Output of a pad stays as you set it. You cannot select pads for the Knob FX.
- A stock project: the mod moves its Knob FX to the master when it loads. When not all pads used it, it starts bypassed: push B3 (Bypass) in FX Select to turn it on for all pads.
Change the Knob FX on any screen
Select another Knob FX effect without leaving your screen.
- Push and hold KNOB FX. The list of effects shows over the screen. The loaded effect is orange.
- Turn the ENCODER to select the next or previous effect in the list.
- Release KNOB FX. The selected effect loads and the list closes. You stay on your screen.
- A short push of KNOB FX sets Knob FX mode on or off at release, as in stock. A hold with an ENCODER turn keeps the mode. KNOB FX + another button or K1-K3 works as in stock.
- The new effect starts with its default values. The change has no undo step, as in stock FX Select.
- The change gives no click: the old effect fades out, and the new effect fades in when its sound is ready (in less than 0.1 s). A bypassed effect stays bypassed.
- The list shows only the effects that are On in Knob FX List.
- This does not work on FX Select, on the Mixer, on the rename screen, when a dialog shows, and when the master has no Knob FX.
Knob FX Bypass on B3
Turn the Knob FX on or off without FX Select.
Changed in 0.3.0: while the KNOB FX bar shows, B3 is now Bypass on every screen. Before, B3 did the function of the screen under the bar. This is on by default. To get the old B3 back, set Settings > Knob FX B3 Bypass to Off.
- Push KNOB FX. The KNOB FX bar shows, and B3 shows Bypass at once.
- Push B3 to turn the Knob FX off (bypass) or on again.
- An orange frame with white text = the Knob FX is on. An orange box with black text = the Knob FX is off (Bypass is on).
- It works on every screen with the KNOB FX bar, for example SAMPLE, Sample Select, SAMPLE RECORD, Step Edit, PAD FX (also on the effect page) and the Tuner. The function of B3 on the screen under the bar (for example Looper on SAMPLE RECORD) is back when you push KNOB FX again to close the bar.
- SHIFT + B3 does the function of the screen, as in stock.
- When a dialog or the NOTE REPEAT bar shows, B3 does their function.
- It is the same switch as B3 (Bypass) in FX Select.
- To give B3 back to the screen under the bar, set Settings > Knob FX B3 Bypass to Off.
Knob FX List and Insert FX List
Hide the effects that you do not use, with a separate list for FX Select and the KNOB FX hold list (Knob FX List), and for the Insert FX list of the Mixer (Insert FX List, also with the insert-only effects).
- In Settings, select Knob FX List > or Insert FX List > and push the ENCODER.
- Select an effect and push the ENCODER to set it On or Off.
- Push B1 or B2 to go back.
- In FX Select, the loaded effect always shows, also when it is Off.
- The lists do not change your project.
- If all effects of a list are Off, that list shows all effects.
Pad FX: Fixed
On the stock Pad FX screen, Fixed holds the effect of a pad after a tap.
- Open the stock Pad FX screen (SHIFT + PAD FX, then B2; see Shortcuts).
- Push B3 to set Fixed on (white box = on).
- Tap a pad. Its effect stays on, also on another screen (as stock Latch), until you tap the pad again. The FADER sets how much of the effect you hear.
- With Fixed on, the FADER has no other function on this screen. Fixed off stops all Fixed effects.
- To keep the FADER menu function of the FADER here, set Fader Overrides > Pad FX (Fixed) to Fader Menu. A tap then holds the effect at the pad velocity.
- Fixed and Latch effects can go into a Resample one pad print.
- A pad with stock Latch on works as in stock, also with Fixed on.
- The MPC keeps the Fixed setting after a restart.
Color Comp. on a track or submix
Put Color Comp. on a track or submix from the Insert FX list (Dynamics). Edit opens its COMPRESSOR screen, with for example "T01" or "Sub 2" at the top (PAD FX = back). SHIFT + PAD 5 opens the master Color Comp., as in stock.
Mother Ducker
Mother Ducker makes a sound softer while another sound plays (a sidechain: for example, the bass gets softer on each kick). Mother Ducker Input goes on the sound that controls it, Mother Ducker on the sound that gets softer. They connect through a bus (Bus 1 to Bus 8).
- Put Mother Ducker Input on the kick (pad, track or submix) from the Insert FX list (Dynamics). Set K1 (Bus), for example Bus 1.
- Put Mother Ducker on the bass. Set K1 (Bus) to the same bus.
- Play both. Set K2 (Threshold) and K3 (Ratio) for how much the bass gets softer.
Under the title, each page shows the other part on the same bus:
| Text | Meaning |
|---|---|
| Input: A01 Kick | Mother Ducker Input on pad A01 controls this Ducker. |
| Input: T02 Bass +1 | Two or more parts are on this bus. The first one shows. |
| Input: A01 Kick (Bypass) | The other part is bypassed (grey): no ducking. |
| No Input on Bus 2 | No other part on this bus (grey): no ducking. Check K1 (Bus) on both parts. |
On the Mother Ducker Input page, the text starts with Ducker:. K1 (Bus) always shows the bus on both pages.
The Mother Ducker page also shows GR (gain reduction, how much softer the sound is now) in dB, with an orange bar (0 to 60 dB). GR 0.0 = no ducking (also with Bypass on).
Tip: The ducking can be more than 60 dB. For a soft ducking, set K2 (Threshold) higher or K3 (Ratio) lower.
| Knob | Mother Ducker | SHIFT + knob |
|---|---|---|
| K1 | Bus (1-8) | Attack |
| K2 | Threshold | Release |
| K3 | Ratio | Soft Knee (dB) |
- A new Mother Ducker starts with the stock values: Bus 1, -6 dB, 6:1, Attack 10 ms, Release 100 ms, Soft Knee 0 dB.
- The Mother Ducker only makes the sound softer: when the Input does not play, the sound is as loud as without it (Auto Make-Up Off, Make-Up Gain 0 dB, not on a knob; stock has Auto Make-Up On).
- Soft Knee makes the start of the ducking softer near the Threshold. At 0 dB the ducking starts at the Threshold.
- Mother Ducker Input is before the pad fader (as in stock): a pad at Vol 0 still ducks.
- To stop the ducking, push Bypass (B3) on the Mother Ducker Input page.
Tip: Put Mother Ducker Input on a pad at Vol 0 to duck to a rhythm that you do not hear.
AIR Compressor and AIR Stereo Width
Two more insert effects: AIR Compressor (Dynamics) and AIR Stereo Width (Modulation).
AIR Compressor starts neutral (0 dB, 1:1). Turn K1 (Threshold) and K2 (Ratio) to hear it.
| Knob | AIR Compressor | SHIFT + knob |
|---|---|---|
| K1 | Threshold | Attack |
| K2 | Ratio | Release |
| K3 | Mix | Output |
AIR Stereo Width with Width at 0 % plays the left and right channel together as one mono sound.
| Knob | AIR Stereo Width | SHIFT + knob |
|---|---|---|
| K1 | Width | Low |
| K2 | Level Trim | Mid |
| K3 | Pan Trim | High |
AIR Lo-Fi
An insert effect that makes a sound lo-fi: fewer bits, a lower sample rate and clip.
- Push PAD FX, select an empty slot of a pad, track, submix or the master, and push B3.
- Select Harmonic > AIR Lo-Fi and push the ENCODER.
- Turn the knobs.
| Knob | AIR Lo-Fi | SHIFT + knob |
|---|---|---|
| K1 | Bit Depth (1 – 16 bit) | Anti-Alias (Off, On) |
| K2 | Rate: the sample rate (500 Hz – 50 kHz) | Post: a filter after the rate |
| K3 | Clip (0 – 40 dB) | Mix (0 – 100 %) |
AIR Lo-Fi starts at 16 bit, 50 kHz, Clip 0 dB and Mix 100 %. There it changes the sound only a little: it cuts the lowest bass (below about 20 Hz).
- Post works only when Anti-Alias is On. With Anti-Alias Off, Post shows --. Turn Post down to make the sound softer and darker.
- Above 44.1 kHz, Rate does not change the sound.
Tip: More Clip makes the sound softer. AIR Lo-Fi has no output gain: turn up the pad or track volume.
AIR Pitch Shifter
An insert effect that changes the pitch and keeps the length of the sound. Tune of a pad changes the pitch and the length together.
- Push PAD FX, select an empty slot of a pad, track, submix or the master, and push B3.
- Select Modulation > AIR Pitch Shifter and push the ENCODER.
- Turn the knobs.
| Knob | AIR Pitch Shifter | SHIFT + knob |
|---|---|---|
| K1 | Shift: -24 – +24 semitones, in steps of 1 | Fine: the same Shift, in steps of 0.1 |
| K2 | Mode: Vocal, Bass, Beats, Chords, Textures | |
| K3 | Mix (0 – 100 %) |
AIR Pitch Shifter starts at Shift 0.0, Mode Vocal and Mix 100 %. Set Mode to the type of sound: Beats for drums, Bass for a bass, Chords for chords.
- The ENCODER steps Shift in semitones: from 7.3, one step up gives 8.0. SHIFT + ENCODER steps 0.1.
- On a track, submix or the master, the effect changes all the sound that goes through it.
Tip: Large shifts and short sounds such as drums can sound less clean. This is normal for a pitch shifter that works while the sound plays.
Kill EQ insert
The 3-band kill EQ of the EQ page is also an insert for a track, a submix or the master, with the same knobs, crossovers and window.
- Push PAD FX. Push B1 for Track or Submix, or B2 for Master.
- Select an empty slot and push B3 (Insert).
- Open EQ/Filter, select Kill EQ and push the ENCODER. The Kill EQ page opens. B3 = Bypass. B1 or PAD FX = back. B3 (Edit) on the slot opens it again.
- The load is one undo step, for example "Kill EQ Slot 1 T01".
- The project saves the Kill EQ values.
- On a track or a submix, the knobs record automation as on the effect page. The knobs keep the last value that played.
Tip: A Kill EQ on the master records no automation, as the stock effects there. For automation on all tracks, send the tracks to a submix with a Kill EQ, put the Kill EQ on each track, or use the EQ page of a pad.
Tip: Without SampQOL OS, the Kill EQ plays as the stock effect PEQ 2-Band, 2-Shelf: the bands do not go to kill, and fully right is +18 dB.
Erasing automation
Erase all automation of a pad
- Hold ERASE and turn a knob or the fader.
- Push B2 (All) in the ERASE PAD AUTOMATION window.
- Push B3 (Do It!). All automation of that pad in this sequence goes: Pad Mute, Filter, EQ, Level, the Insert FX of the pad and more. The notes stay. The Insert FX of the track stay.
- UNDO works.
- B2 (All) also works in Mute mode (ERASE + pad).
- When there is nothing to erase, the MPC shows "No automation to erase." Stock shows nothing.
- See also Settings > Erase All Starts.
Tip: Does your recording sound strange and you do not know which automation causes it? Erase all automation of that pad.
Erase all automation of a track
- Hold MUTE for 0.7 seconds (Track Mute). The pads are the tracks.
- Hold ERASE and push the pad of the track.
- Push B2 (All) in the ERASE TRACK AUTOMATION window.
- Push B3 (Do It!). All automation of that track in this sequence goes: track mutes, Track Volume, the Insert FX of the track, the automation of all its pads (also their Insert FX), and recorded MIDI CC (sustain pedal, mod wheel) and aftertouch. The notes stay.
- B3 without B2 (All): only the recorded track mutes of that track in this sequence go.
- UNDO works.
Erase the track volume
- Set the FADER to Track Volume (see Track Volume on the FADER).
- Hold ERASE and move the FADER. The ERASE TRACK AUTOMATION window opens for the current track.
- Push B3 (Do It!). The recorded volume of the current track in this sequence goes. Other tracks and the notes stay.
- UNDO works.
- B2 (All), then B3: all automation of the current track in this sequence goes, as in Erase all automation of a track.
Erase automation in the mixers
In the Ch. Mixer, the Pad Mixer, the insert pages and the effect pages, you erase the recorded automation of one strip: a track, a submix or a pad.
-
Push B2 to open the Ch. Mixer or the Pad Mixer. Turn the ENCODER to select the strip.
-
Hold ERASE and move a control of the strip:
- K1 or the FADER: the volume (the Level of a pad).
- K2: the pan.
- B3: the mute.
The ERASE TRACK AUTOMATION, ERASE SUBMIX AUTOMATION or ERASE PAD AUTOMATION window opens. It shows the strip, the sequence and the control.
-
Push B3 (Do It!). The recorded automation of that control in this sequence goes. The other strips and the notes stay.
- B2 (All), then B3: all automation of that strip in this sequence goes. On a pad: mute, solo, Level, Pan, Insert FX and more. On a track or a submix: mute, volume, pan, Insert FX and more.
- B1 (Cancel) closes the window. The window also closes when the sequence changes.
- When there is nothing to erase, the MPC shows "No automation to erase."
- UNDO and REDO work. The current track stays.
- The master strip has no automation: ERASE shows "No automation on the master."
- ERASE + K3 does nothing. ERASE + a pad works as in stock.
- On an insert page (Pad, Track, Submix): ERASE + K1 = the volume (the Level of a pad). ERASE + ENCODER push = the on/off of the selected effect. ERASE + B3, K2 or K3 does nothing.
- On an effect page of a pad, a track or a submix: ERASE + K1, K2 or K3 = the parameter of that knob. ERASE + B3 = the on/off of the effect. On the Kill EQ page, K1-K3 = Low, Mid, High. For the SHIFT layer (and the Kill EQ crossovers), use All.
- With the FADER menu Off, ERASE + FADER does nothing.
- With Knob FX mode on, ERASE + K1 or K2 erases Knob FX automation, as in stock. While NOTE REPEAT shows, B3 is its division.
- See also Settings > Erase All Starts.
Loading and saving
Preview in Sample Select
In Sample Select, the pads preview the file. With Own Sample, a pad with a sample plays its own sound, to compare a file with your kit.
- Push SAMPLE SELECT and select an audio file.
- Push a pad. It becomes the selected pad (where a load goes) and plays the file to the end.
- Turn K3 (Prev. Vol.) to set the preview volume.
Tip: When a long folder name hides Prev. Vol., hold SHIFT to see it.
To compare the file with your kit:
- Turn SHIFT + K2 to the right (Own Sample).
- Push a pad that has a sample. It plays its own sound, and the selected pad does not change. The selected pad or an empty pad plays the file.
- Turn SHIFT + K2 to the left for Preview again.
B3 (Preview) is the stock auto-preview on/off. SHIFT + B3 is the stock Delete on the SD card.
Tip: The MPC keeps the K2 choice (Settings > Sample Select Pads Play). To load onto a pad with a sample in Own Sample, set Preview, or select the pad before you push SAMPLE SELECT.
New folder in Sample Select
- Push SAMPLE SELECT. Push B2 to select External (the SD card).
- Go to the folder where the new folder must go, and select a folder in it (in an empty folder, nothing is selected). B3 shows New Folder.
- Push B3. Type the name, as in stock.
- Push B3 (Do It!). B1 (Cancel) makes no folder.
If the name exists, the MPC makes no folder and shows "A folder with this name already exists" (B3 = OK). Internal is read-only: there, B3 does not show New Folder.
Delete folder in Sample Select
- Push SAMPLE SELECT. Push B2 to select External (the SD card).
- Select the folder. Hold SHIFT: B3 shows Delete Folder in red.
- Push SHIFT + B3. The MPC shows the name of the folder.
- Push B3 (Delete). The folder and all files and folders in it are deleted. B1 (Cancel) deletes nothing.
Warning: You cannot undo this. The files are gone from the card.
- You cannot delete the folder of the loaded project, a folder above it, or its [ProjectData] folder. The MPC shows "This folder holds the loaded project". Stock saves the project back there.
- A large folder can take some time. The MPC then shows "Deleting..." with the number of deleted files. The message closes when the delete is done.
- If some files cannot be deleted, the MPC shows "Could not delete all of it".
- On a folder, SHIFT + B3 does not switch Auto Preview. Select a file to switch it.
- Internal is read-only: there, SHIFT + B3 does not show Delete Folder.
Browser
- In SAMPLE SELECT and Load Project, hold SHIFT and turn the ENCODER to jump 10 rows.
- In SAMPLE SELECT and Load Project, move the FADER to scroll the list (up = the first row). For the FADER menu function there, set Fader Overrides > Sample Select to Fader Menu.
- The browser remembers your place in each folder.
- Start Drive in Settings sets the drive at the start: SAMPLE BROWSER for Sample Select, PROJECT for Load Project.
- The browser does not show the autorun folder (SampQOL OS) in the root of a drive. Use a computer to see it.
- After an Eject of the SD card (SHIFT + B2), the card has the same path when you put it in again, so your Home Folder and Export folder stay correct. In stock, the card often got a new path.
Load Kit
Load Kit loads a kit into the current track. The samples of the other tracks stay. A kit sample with the same name as a sample in the project gets its own name (for example Kick1), so each track keeps its own sound. The track gets the name of the kit.
A .mpcsample kit (a folder with WAV files, for example from a sample pack) loads the same way. All pads of the track start with the default settings (tune, filter, envelope). One UNDO removes the kit.
Tip: Load Kit loads only the samples of a .mpcsample kit, not its mute groups.
A drum program (.xpm): Load Kit also loads the samples of a drum program file (.xpm) from the MPC software or an MPC Live, One or X. The Load Project list shows the .xpm files.
- Push SHIFT + PAD 16, then select Load Project.
- Go to the folder with the .xpm file. Its WAV files must be in the same folder.
- Select the .xpm file, then push B3 (Load Kit).
The samples go onto the current track, on the same pads as in the program. All pads start with the default settings. The pad colours do not change. The track gets the name of the program. One UNDO removes the kit. A .xpm file does not load as a project: the ENCODER push on it shows "Use B3 Load Kit for a .xpm file."
Important: A .xpm file loads only the samples. The insert effects, the effect settings, the pad settings (level, pan, tune, envelope, filter) and the mute groups of the program do not load.
Tip: When a WAV file is not in the folder, its pad stays empty and a message shows how many samples were not found. When a sample cannot be copied into the project (for example, the storage is full), its pad also stays empty and the message shows how many samples were not copied. Only drum programs load: a keygroup, plugin, MIDI or audio program shows a message and loads nothing.
Unique track names: the project saves the notes of each track under the track name. Thus when Load Kit or Load Project gives two tracks the same name, the second track gets its own name, for example Drum 001-2.
Save to a folder
Save Sample and Save Project save in a folder that you choose.
- Open the name screen: SHIFT + SAMPLE SELECT (Save Sample), or SHIFT + PAD 16 and Save Project.
- Type the name, as in stock.
- Push B3 (Do It!). The folder page opens in the folder of your last save. Save Project with the name of the loaded project opens in the folder of that project.
- Turn the ENCODER to select a folder. Push the ENCODER to open it. B1 (Up) goes one folder up (in the root of a drive: back to the name screen, no save). B2 selects Internal or External.
- Push B3 (Save). The MPC saves in the folder that the page shows.
For a name that exists, the MPC asks "Sample Already Exists" (as in stock) or PROJECT EXISTS (B3 = Overwrite, B1 = Cancel).
Tip: After start-up, the folder page opens in the stock folder (Samples/User or Projects/User; on the SD card: Projects), on the Start Drive of Settings.
Home Folder
Sample Select always opens in your own folder.
- In Settings, select Home Folder and push the ENCODER. The folder page opens.
- Select a folder as in Save to a folder (step 4).
- Push B3 (Use Folder). B1 (Back) in the root of a drive goes back with no change.
- Set Sample Select Opens to Home Folder.
Each time you push SAMPLE SELECT, the browser opens in the Home Folder. After you load a sample with the ENCODER, a message or a SHIFT menu, the browser stays where you were.
Tip: If the Home Folder is not there (deleted, or no SD card), Sample Select opens on the Start Drive of SAMPLE BROWSER.
Random project name
- Go to Save Project (SHIFT + PAD 16).
- Hold SHIFT and push B3 (Random). The name field shows a random name, for example "Velvet Alley". Push again for a different name.
- Push B3 (Do It!) and select the folder (see Save to a folder).
New project with a template
- Open Settings and select Default Template. Push the ENCODER.
- Select a project (internal or SD card) and push the ENCODER. None = no template.
New Project asks: B1 = No, B2 = Empty (as in stock), B3 = Template. The template itself does not change: Save Project suggests the name "project".
Export mixdown and stems
Export makes WAV files (24-bit, 44.1 kHz) of a sequence.
- Save your project and stop the sequence.
- Push SHIFT + PAD 16, then B3 (Export).
- Select a row with the ENCODER. Push the ENCODER or turn K1 to change the value.
- Push B3 (Export). You cannot stop an export.
| Row | What it does |
|---|---|
| Sequence, Start, End | The sequence (only sequences with events, for example S01 Intro (16 bars)) and the bars. |
| Export Mixdown | One WAV of the full mix. |
| Mixdown Master FX | The mixdown includes the master effects (also Knob FX). The stems never have them. |
| Export Stems | One WAV for each track, with its submix effects. Together they sound as the mix without the master. A track that is muted in the sequence, or has no notes there, gives no file. A muted track that a recorded track mute unmutes gives a file. The recorded track mutes of a track play only in its own stem. |
| Tail | Extra time after the end, for reverb and delay. |
| Folder | The destination folder (push the ENCODER). Default: Samples/User/Export on the SD card. |
| Stems Folder | Subfolder: the stems go in the folder Stems. Same: next to the mixdown. |
| BPM in Name | The tempo in no file name (Off), the mixdown name (Mixdown) or all names (Mix + Stems). |
| Separator | " - " or "_" between the parts of the file name. |
-
The files go into a folder with the project name. The file names start with the project name; a stem also has the track number and name. Examples for "MyTrack" at 81 BPM:
BPM in Name Separator Mixdown Stem Off " - " MyTrack.wav MyTrack - Tr01 - Drums.wav Mix + Stems " - " MyTrack - 81 BPM.wav MyTrack - 81 BPM - Tr01 - Drums.wav Mix + Stems "_" MyTrack_81BPM.wav MyTrack_81BPM_Tr01_Drums.wav -
When you export only some bars, the name also has the bars, for example MyTrack - b2-5.wav.
-
If a file exists, select B2 (Keep Both) or B3 (Replace).
-
Without space, the MPC shows "Not enough space". An export to the internal storage stops when less than 200 MB is free.
-
If the card cannot save a file, the export stops with EXPORT FAILED, the file and the number of files that are OK. Push B3 (OK). Check the card on a computer, or use another card.
Tip: All sequences of a project get the same file name. To keep the export of each sequence, select Keep Both, or set BPM in Name when the sequences have different tempos.
Resample one pad
SampQOL OS can also resample one pad, as Flatten Pad on the large MPC.
- Select the pad that you want to resample.
- Push SHIFT + PAD 11 (Resample):
- B1 = Cancel.
- B2 = Pad: only the selected pad, one hit, with tail.
- B3 = Seq: the full sequence (stock).
- With Pad, the line under "Select pad" shows which effects go into the new sample, for example Print Knob FX: On Pad FX: Off (On = the effect is on and its print is on). SHIFT + B3 (Knob FX) and SHIFT + B2 (Pad FX) set each print On (white box) or Off (white frame). The MPC keeps your last choices.
- With Pad, turn K1 or the ENCODER (1 second per step) to set the Tail (0 to 10 seconds, default 2). The tail is in the new sample only when an effect is in it (a pad insert, Knob FX or Pad FX). The MPC keeps the value. When the KNOB FX bar shows, K1 is the stock Knob FX function. A Sample Tail of the pad is always in the new sample, with the time that its fade needs.
- Push the destination pad.
- In the new sample (then reset on the destination pad): tune, filter, envelopes, LFO, warp, start/end/loop, Offset, Sample Tail, layers and pad inserts. Stays on the destination pad: route, sends, mute targets, Mono/Poly, Mute Group, Amp Vel Sens and the KEYS root note, so a MIDI keyboard plays the new pad at the same pitch.
- Print On: the Knob FX or the Pad FX that are on are in the new sample, with the Tail. With Knob FX, the new sample has the volume of the source pad and the destination pad stays at 0 dB. With both Off, the new sample has no effects and the destination pad gets the volume of the source pad.
- Chops: a chopped sample gives the new sample the same chops, at the same places in the sound (Tune, Warp and Reverse move them with the sound). Chops outside Start and End go. The destination pad gets Chop Type Manual. UNDO puts the old sample back, with its chops. Extract pads of the old sample do not change. No chops when the pad plays one chop only, or has more than one layer with a sample.
- Track and submix effects and the other master effects are not in the new sample. A Hidden Knob FX or Pad FX is in it with its print On; other Hidden effects are not. Use a pad insert for that, or RECALL (SHIFT + SAMPLE RECORD): it records the last 25 seconds of the master output, with all master effects.
Tip: The new pad also plays through the Knob FX and the Pad FX that are on. With the print On you then hear the effect two times. Turn the effect off after the resample, or set the print to Off.
Tip: A pitch envelope, a pitch LFO or random pitch changes the speed during the sound. The chops then move by the mean speed, so they can be a little early or late. Check them in Chop Mode.
Tip: To put a Pad FX into the new sample, turn it on with Fixed or stock Latch (hold the pad and push B1) before SHIFT + PAD 11. An effect that you hold with your finger stops when you leave the Pad FX screen (stock). A Reverb or a Delay with much feedback needs more than 2 seconds of Tail.
Undo and Redo
Undo counter
SHIFT + - (Undo) and SHIFT + + (Redo) show a popup with the name of the step and a counter, for example Undo 2/7:
- The first number is the quantity of steps that you undid.
- The second number is the quantity of steps that the MPC keeps.
Example: three pushes of Undo show Undo 3/7. One Redo then shows Redo 2/7. Redo 0/7 = all steps are done again.
- The MPC keeps a maximum of 512 steps. Then the oldest step goes.
- Load Project and New Project delete all steps.
- A knob turn without a stop is one step. A stop of more than 0.5 seconds starts a new step.
- With no step to undo or redo, the MPC shows no popup.
- Undo and Redo also work on SAMPLE RECORD.
- Each Normalize, Trim, Extract and Resample keeps its version in its own sample file, so an Undo never removes a sample that an older step needs. The MPC deletes old versions when you start the MPC or load a project.
- A sample on no pad does not go into the saved project. The MPC deletes it at the next start, as stock does.
Step names
The popup of a SampQOL OS step shows what changed (first line) and where (second line, for a name longer than 14 characters). Examples:
| Popup | Meaning |
|---|---|
| Copy A01 / to T04 A02 +2 | Pad A01 copied to A02 of track 4 and 2 more pads |
| Extract A01 / to T02 A01-A16 | The chops of A01 extracted to a new track 2 |
| Velocity / S01/T01 A05 | Step Edit: K3 changed pad A05 in sequence 1, track 1 (also Nudge, Length) |
| Erase S01/T01+2 | Step Edit (Track View): track 1 and 2 more tracks |
| Effect Off / Slot 1 A01 | Pad Mix: the effect in slot 1 of pad A01 is off |
Stock steps keep their stock name, for example Add Event.
Screen Mirror
The MPC screen shows live in a browser on your computer. Use it to make tutorials or videos, or to see the screen better. The browser shows the same as the MPC screen. You cannot control the MPC from the browser.
- Connect the MPC to the computer with the USB cable.
- On the computer, open a browser and go to http://mpc-sample.local:7410.
The screen of the MPC shows in the browser. Make the window larger to make the screen larger.
Tip: If the address does not open, use http://192.168.155.1:7410. See also Screen Mirror does not open.
Tip: Make a bookmark of the address. In OBS, add the address one time as a Browser source (size 320 x 240, or a larger size with the same shape).
Tip: The MPC Sample has no WiFi. Screen Mirror works only with the USB cable.
Tip: Screen Mirror uses CPU only while a browser shows the screen. Close the browser tab when you are done.
Sleep
The MPC goes to sleep when you do not use it for some time. The screen and all pad and button lights go off. This saves the battery when you take a break. The sound does not stop: USB audio and the input monitor stay on.
- Open Settings.
- Go to SYSTEM > Sleep and select the time: 5 min, 10 min, 20 min or 30 min. Off = no sleep (only the stock screensaver, which dims the screen).
To wake the MPC, push a button, hit a pad or turn a knob. The first touch only wakes the MPC: a pad does not play and a button does nothing.
Tip: The MPC does not go to sleep while a sequence plays, while the SAMPLE RECORD screen shows, while the Looper runs or while a question shows on the screen.
Tip: MIDI from a keyboard or a computer keeps the MPC awake, and it wakes the MPC. That MIDI note also plays.
Tip: Sleep does not turn the MPC off. To turn it off, use POWER.
Compatibility and limitations
SampQOL OS works only on MPC Sample firmware 1.3.0. It is tested only with MPC Sample 1.3.0. Projects on an MPC One, Live or X (MPC OS 3.9.1) are not tested yet.
The mod writes what the MPC project format already has (notes, samples, mutes, drum tracks, inserts). Other data goes into the file .sampqol in the [ProjectData] folder, which stock and the MPC One, Live and X ignore. When you copy a project, copy the full [ProjectData] folder.
Tip: Save your SampQOL OS projects in a separate folder. Before you open one on a stock MPC Sample, make a copy.
Your project on another MPC
| Function | MPC Sample, stock 1.3.0 | MPC One, Live, X (3.9.1) |
|---|---|---|
| To Seq, Looper, Resample one pad, KEYS, Scale | Works: normal notes and samples. | Works. |
| More drum tracks | Loads only the first track. The project safety net keeps the others. | All tracks load. |
| Pad EQ | You do not hear the EQ. | You do not hear the EQ. Pad EQ Off = hear the project as there. |
| Stereo (one channel) | The pad plays both channels. | The pad plays both channels. |
| Kill EQ insert | Plays as a PEQ 2-Band, 2-Shelf (no kill, +18 dB). | Plays as a PEQ 2-Band, 2-Shelf (no kill, +18 dB). |
| AIR Compressor, AIR Stereo Width, AIR Lo-Fi, AIR Pitch Shifter, Mother Ducker | Loads and plays, with the values set in SampQOL OS. A save keeps the effects. | Probably plays: these are stock MPC effects. Not tested yet. |
| Recorded pad mutes | The mutes do not play. | The mutes probably play. |
| Track mutes for each sequence | All tracks sound. | Not tested yet. |
| Mute groups of tracks and submixes | A mute acts on one track or submix only. | Not tested yet. |
| Pad mute with Mute Type Event | Sounds as Audio: the sound of the pad stops at once. | Probably sounds as Audio. |
| Knob FX on all pads | As in stock: an insert on Submix 1. In the mod again, it goes back to the master. | Plays as master insert 4. |
| Removed or Hidden master effects | Stock puts Pad FX, Flex Beat and Color Comp. back. A Hidden effect does not play. | A Hidden effect does not play. |
| Track Volume (FADER) | You do not hear the track volume. | Probably plays as the track volume. |
| Input FX | Loads and plays the input effects. The Input FX page and the Input strip are not there. | Not tested yet. |
| MIDI channel of a track | All pads send with the MIDI Out Channel and Pad MIDI Out of MIDI Config, also a track with Off. A 16 Levels pad sends its source note. | Probably sends on the track channel, also with Pad MIDI Out Never; Off probably sends nothing. A 16 Levels pad sends its source note. |
| Random project name, Template | A normal project. | A normal project. |
| Settings, Knob FX List, Insert FX List, Sample Select preview | Not in the project. | Not in the project. |
The column MPC One, Live, X is based on the project format. It is not tested yet.
Limitations
The limitations that change how you use a function are also a Tip in its section.
- Chords on one pad. A KEYS or Scale chord is on one pad. On a stock MPC, a chord on a pad in Note On mode stops at the shortest note. ERASE, Mute and Solo act on all tones of that pad.
- Screen Mirror. Only with the USB cable, and you can only look: the browser does not control the MPC.
- Sample key. A project saved by a stock MPC Sample can have a key on every sample, also on drum hits: stock guesses a key for each sample and saves it. Set such a key to Off with the Tuner (Key mode, "No key found", Apply) or by hand.
- KEYS. A key adds no event in Step Edit (as in stock). The same note on a key and on a held 16 LEVELS pad stop each other at release (as in stock).
- Knob FX. All pads play through it. See Knob FX on all pads.
- Input FX. The Knob FX, Pad FX, Flex Beat and Color Comp. do not play on the input. See Input FX.
- Automate. See the Tips in Automate.
- Stereo. Elsewhere, the pad plays both channels. See Stereo.
- Track Volume. Only for pads with their output on the track. See Track Volume on the FADER.
- Mute groups of tracks and submixes. A stock MPC does not know them. A recorded mute plays on each track, as recorded.
- MIDI out. Two held pads on the same note and channel play one note. No undo for the MIDI setting. One MIDI Port for all tracks. See MIDI out.
- Track mutes on stock. A stock MPC Sample does not play track mutes per sequence (also after Song Export). See Track mutes per sequence.
- Audio track mute and pad outputs. A pad with Out set to a submix or an output stops at once, with a click (as in stock). See Mute Type.
- Explode and Mute Targets. See Explode.
- Swap between tracks. Only when one of the two tracks has a pad without a sample. See Copy a pad to another track.
- 16 USB outputs. A few seconds more to start. Only tracks and submixes, no pads. Without the setting, or on a stock MPC Sample, the load shows "Unsupported Outputs": RESOLVE sets these outputs to the Master. After a restart in SD Card Access, restart the MPC again to get them back. See 16 USB outputs.
- USB audio delay. The USB audio to the computer is about 5 ms later than the MPC outputs. Your DAW does not know this delay. See 16 USB outputs.
- Internal storage. The internal storage always keeps about 400 MB free. When an edit or a save needs more, the MPC shows "Insufficient space on drive". A sample from the SD card is copied to the internal storage, and Normalize makes a second, larger copy (until the next start). Thus long samples fill the internal storage quickly. SampQOL OS removes the old copy of a long sample after an edit or a new chop (stock keeps it until the next save or load). See Troubleshooting.
- Memory for big projects. Load Project and Load Kit do not load a project that is too big for the free memory (RAM). Each load of a big project keeps some memory in use until the next start, so a big project can load after a start but not after some other loads. See Troubleshooting.
Troubleshooting
The display does not show the SAMPQOL logo at start-up
- The folder autorun must be directly on the card.
- The card must have the format exFAT. Formatting deletes all on the card.
- Mac: Disk Utility > select the card > Erase > ExFAT.
- Windows: File Explorer > right-click the card > Format > exFAT > Start.
- Do not change or open the files in the folder: the MPC ignores a changed folder. Copy the folder autorun from the zip file again.
- The firmware must be 1.3.0 (step 1 of Install). On other firmware, the MPC starts as stock.
The display does not show v1.3.0
The display shows only v1.3.0 for the correct firmware 1.3.0.12.
- Lower than 1.3.0: install 1.3.0 with the MPC Sample 1.3.0 Updater. Do not install a higher version.
- Higher than 1.3.0: do not use the mod on this firmware.
With the SD card in, the MPC is stock
- Set the MPC off and on again.
- Still stock? Check the firmware version (step 1 of Install).
The start-up stops at 0.0%
Push B1. The MPC then continues the start-up.
The MPC hangs at start-up, or SampQOL OS does not work
The MPC does not ask a question at start-up, so you cannot select stock there. Do these steps:
- Push and hold the power button until the MPC goes off.
- Remove the card. Set the MPC on. It is stock again.
- To try SampQOL OS again, put the card back in. SampQOL OS starts at once. If the problem stays, do step 1 and 2 again, then step 4.
- On a computer, rename or move the folder autorun (see Go back to stock). Your projects and samples on the card do not change.
- Put the card back in the MPC. Stock uses the card at once.
The files events.log and last-exit.log in its folder logs show what happened.
The installation is correct, but SampQOL OS does not work
Also when the card has the format exFAT already:
- Copy your projects and samples from the card to the computer. Formatting deletes all on the card.
- Format the card again as exFAT (see The display does not show the SAMPQOL logo at start-up).
- Do all steps of Install again. Do each step exactly as written.
Insufficient space on drive
This message is about the internal storage, not the SD card. The internal storage always keeps about 400 MB free.
- Push B1 (Clear) to delete the undo history. This gives back the space of the samples that only the undo history used.
- Set the MPC off and on. This gives back the rest of the space.
- Save your projects and samples on the SD card.
- Keep the internal storage as stock as possible. Move your own projects and samples from the internal storage to the SD card.
Not enough memory
The project or kit is too big for the free memory (RAM). The MPC does not load it. Your open project stays as it is.
- Push B3 (OK).
- Save your project.
- Set the MPC off and on. This gives back all the memory.
- Load the project again.
Tip: Only very big projects need this, for example 16 tracks with about 60 full sequences. A smaller project uses less memory: delete the sequences that you do not use.
An external synth follows the tempo but plays no notes
The MIDI clock goes out, but the notes of the track do not.
- Push SHIFT + PAD 8 to open MIDI Config.
- Set Pad MIDI Out to Always. With When Empty, only pads with no sample send MIDI. With Never, no pad sends MIDI. This is also true for a track with its own MIDI channel.
- Make sure that the track and its pads are not muted. A muted track or pad sends no MIDI notes.
See MIDI out: a track plays an external synth for the MIDI channel of a track.
The MPC goes back to stock while you play
The mod crashed two times within 2 minutes. Set the MPC off and on to get SampQOL OS back. The files events.log and last-exit.log in autorun/logs on the card show what happened.
The computer lost the SD card
SampQOL OS crashed during SD Card Access. The watchdog disconnects the card from the computer before the MPC uses it again, so they do not use the card at the same time.
- Wait until SampQOL OS has started again.
- Open SD Card Access again (SHIFT + PAD 16).
- On the computer, check the files that you copied last. Copy them again if they are not complete.
The file events.log in autorun/logs on the card shows the line "in SD Card Access: USB set back to normal".
Screen Mirror does not open
- Make sure that the USB cable connects the MPC to the computer, and that SampQOL OS has started.
- Use the address http://192.168.155.1:7410. Some browsers (for example Firefox) do not find mpc-sample.local.
- On a Mac, the browser must have access to the local network. Open System Settings > Privacy & Security > Local Network, set your browser (or OBS) to on, then close the browser and open it again. Firefox shows "Unable to connect" without this access.
Copyright and trademarks
SampQOL OS (c) 2026 Snare Bes. All rights reserved. See LICENSE.txt.
Akai Professional, MPC and MPC Sample are trademarks of inMusic Brands, Inc.
SampQOL OS © 2026 Snare Bes. All rights reserved. Not a product of Akai Professional or inMusic.